User manual RUSSOUND CAA66 1

[. . . ] CAA66 Multisource Multiroom Audio Controller/Amplifier IMPORTANT SAFEGUARDS 10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. [. . . ] FIXED/VARIABLE SWITCH - Change line out between fixed and variable output. COMMON IR OUTPUT - Output jack passes all IR signals from all keypads. SOURCE IR OUTPUTS - Six source-specific IR Output jacks allow IR control of source equipment. SOURCE INPUTS - Six pair of Audio Line Level input connections for CAA66 source components. 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INSTALLER COMPONENT GUIDE Keypad Update Port The KPSC 12-pin header and the update jumper for the KP6 (and KPL) are located on the right side of the keypad when facing front. Note: The update pins on the KP6 are accessed from the side when the keypad is not installed. 3 1 AM/FM XM1 CABLE SERVER 1 1 2 OS UPDATE/RUN JUMPER -The pins are jumpered when performing a firmware update on the keypad. KPSC PORT - 12-pin header for connection to KPSC source control keypad OS UPDATE PORT - Used to update the KP6 and KPL keypad operating system firmware. If an update is released, it will be available online through the Document Center on www. russound. com. Look in the "Firmware and Downloads" section under Multi-Zone product type. The Advanced Programming Cable is available from Russound, Part #2500-521065. 3 Source 2 KP6 Front View 3 KP6 Top View 1 Jumpered pins KP6 Side View 17 INSTALLER COMPONENT GUIDE Keypad Rear Panel and Installation CAT-5 to KP6/KPL Connection The KP6/KPL keypad uses a 110punchdown terminal on the back panel to provide simple installation and a strong connection for CAT-5 cable's eight conductors. Attach the CAT-5 cable to the 110-punchdown terminal on the KP6 keypad as shown, matching the conductor colors to the connection color guide. The keypad will not operate properly if the terminations deviate from the required connection order. Take care when using an impact 110 punchdown tool, as this may overspread the contact points. Use of the impact tool may propel stray bits of wire and jacket into the keypad's chassis and possibly cause a short in the circuitry. Gently shake or blow air through the keypad chassis to remove stray wire before the keypad is installed into the junction box. Source Label Installation Note: Source labels must be inserted prior to installing the trim plate on the keypad. 1. Determine the system's source names and numbers (e. g. , CD, Source 1). Select the corresponding source name label from the included label sheets. Left-side labels are used for sources 1, 3 and 5; right-side labels are used for sources 2, 4 and 6. Slide the label into the window slot until the source name is centered in the window. KP6/KP4 Source Labels Keypad Installation 1. Ensure it is possible to route the wire to the location you have chosen. To install a single-gang keypad, you will need to use a UL/CSA approved plastic single-gang (18 ci) electrical box. Use a 110 punchdown tool to connect each wire to its corresponding color labeled on the punchdown terminal. For the KP6 keypad, insert the source name labels in the appropriate slots before attaching the back plate and trim plate. Electrical Box Source AM/FM CABLE XM1 SERVER1 KP6 Keypad Back Plate Trim Plate 18 INSTALLER MAKING CONNECTIONS Keypad Port Connection The Keypad Ports are located on the back of the CAA66 in the top left of center. [. . . ] Press the Source button to toggle through the menu options, and use the Volume Up/Down buttons to scroll through the selections. When finished, press and release the Setup button again. KPL Setup Menu SOURCE SOURCE FACT INIT Procedure SOURCE Yes Are You Sure? No KPL Diagnostics Menu The Diagnostics Menu allows the installer to run a diagnostic check on the keypad and to verify the firmware version of the keypad. To access the Diagnostics Menu, press and hold the Setup button on the right side of the keypad until "Diags" appears on the display. When finished, press and release the Setup button. Press and Hold Setup Button KPL Diagnostics Menu DIAGNOSTICS SOURCE CONTROLLR ID PORT ID SOURCE SOURCE KEYPAD ID SOURCE VERSION SOURCE Displays Controller ID number Displays Port ID number Displays Keypad ID number Displays current firmware version BUTTON TEST SOURCE DISP CHAR SOURCE DISP BLOCK SOURCE DISP ROW SOURCE Press button to be tested Press Vol Up/Dwn to scroll characters Press Vol Up/Dwn to scroll blocks Press Vol Up/Dwn to scroll rows 41 REFERENCE SOURCE NAMES - KPL KEYPAD 5-Character Display Description 5-Character Display Description 5-Character Display Description Aux Aux 1 Aux 2 Blues Cable Cbl 1 Cbl 2 Cbl 3 CDCh CDCh1 CDCh2 CDCh3 CD CD 1 CD 2 CD 3 Clscl Cmptr Cntry Dance DigCb 42 Auxiliary Auxiliary 1 Auxiliary 2 Blues Cable Cable 1 Cable 2 Cable 3 CD Changer CD Changer 1 CD Changer 2 CD Changer 3 CD Player CD Player 1 CD Player 2 CD Player 3 Classical Computer Country Dance Digital Cable DSS DSS 1 DSS 2 DSS 3 DVDCh DVDC1 DVDC2 DVDC3 DVD DVD 1 DVD 2 DVD 3 FDoor Hers His www. [. . . ]