User manual RUSSOUND CAA66

[. . . ] CAA66 Multisource Multiroom Audio Controller/Amplifier Installation Manual IMPORTANT SAFEGUARDS 10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. [. . . ] this may require moving it until the front edge hangs clear of the shelf. Place a flat screwdriver blade in the bottom slot on the left and right between the cover and the controller. Twist the blade, then lift the bottom panel up and off. Place a flat screwdriver blade in the bottom slot on the left and right between the cover and the controller. Twist the blade to loosen the cover from its catches. Grasp the panel on each side and gently lift the panel up and off. Panel removed from controller 15 INSTALLER COMPONENT GUIDE Controller Back Panel 1 2 3 4 5 6 7 8 15 1 2 14 13 12 11 10 9 CONTROLLER LINK IN AND LINK OUT - Links multiple CAA66 controllers and peripherals. RS-232 INTERFACE - The RS-232 Interface allows the zones to be controlled by PC or other devices that have an RS-232 Interface, allows for firmware updates and programming. KEYPAD PORTS - One KP6/KPL Keypad Port for each of the six CAA66 Zones. MUTE 12VDC TRIGGER IN - Applying 12VDC to the Mute 12VDC Trigger In jack will mute audio for assigned CAA66 Zones. 12VDC TRIGGER OUT - 12VDC 100mA Trigger Out turns on when any zone is on, and turns off 5 minutes after the last zone is turned off. AC-240V/AC-110V Switch - Switches A/C input voltage between 240VAC and 110VAC. FUSE HOLDER - Holds a replaceable fuse for A/C input connection: 110VAC operation - F3A H 250V; 240VAC operation, T1. 25A H 250V. AC 120/240 INPUT - Grounded 3-terminal plug detachable power cord connection. ZONE OUTPUTS - Detachable color-coded modular 8-ohm speaker connectors for each zone. FIXED/VARIABLE SWITCH - Change line out between fixed and variable output. COMMON IR OUTPUT - Output jack passes all IR signals from all keypads. SOURCE IR OUTPUTS - Six source-specific IR Output jacks allow IR control of source equipment. SOURCE INPUTS - Six pair of Audio Line Level input connections for CAA66 source components. 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INSTALLER COMPONENT GUIDE Keypad Update Port The KPSC 12-pin header and the update jumper for the KP6 (and KPL) are located on the right side of the keypad when facing front. Note: The update pins on the KP6 are accessed from the side when the keypad is not installed. 3 1 OS UPDATE/RUN JUMPER -The pins are jumpered when performing a firmware update on the keypad. KPSC PORT - 12-pin header for connection to KPSC source control keypad. OS UPDATE PORT - Used to update the KP6 and KPL keypad operating system firmware. If an update is released, it will be available online through the Document Center on www. russound. com. Look in the "Firmware and Downloads" section under Multi-Zone product type. The Advanced Programming Cable is available from Russound, Part #2500-521065. 1 2 3 2 KP6 Front View 3 KP6 Top View 1 Jumpered pins KP6 Side View 17 INSTALLER COMPONENT GUIDE Keypad Rear Panel and Installation CAT-5 to KP6/KPL Connection The KP6/KPL keypad uses a 110punchdown terminal on the back panel to provide simple installation and a strong connection for CAT-5 cable's eight conductors. [. . . ] Press the Source button to toggle through the menu options, and use the Volume Up/Down buttons to scroll through the selections. When finished, press and release the Setup button again. KPL Diagnostics Menu The Diagnostics Menu allows the installer to run a diagnostic check on the keypad and to verify the firmware version of the keypad. To access the Diagnostics Menu, press and hold the Setup button on the right side of the keypad until "Diags" appears on the display. When finished, press and release the Setup button. 41 REFERENCE SOURCE NAMES - KPL KEYPAD 5-Character Display Description 5-Character Display Description 5-Character Display Description Aux Aux 1 Aux 2 Blues Cable Cbl 1 Cbl 2 Cbl 3 CDCh CDCh1 CDCh2 CDCh3 CD CD 1 CD 2 CD 3 Clscl Cmptr Cntry Dance DigCb 42 Auxiliary Auxiliary 1 Auxiliary 2 Blues Cable Cable 1 Cable 2 Cable 3 CD Changer CD Changer 1 CD Changer 2 CD Changer 3 CD Player CD Player 1 CD Player 2 CD Player 3 Classical Computer Country Dance Digital Cable DSS DSS 1 DSS 2 DSS 3 DVDCh DVDC1 DVDC2 DVDC3 DVD DVD 1 DVD 2 DVD 3 FDoor Hers His www. [. . . ]