User manual RUSSOUND BGK3

[. . . ] iBridge Power Dock Kit Installation Manual BGK3 SAFETY INSTRUCTIONS 6. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. [. . . ] Temporarily plug the BGDA Dock Adapter into a live AC outlet near the BGCA to perform binding assurance procedure. Bind the system To bind the two adapter devices, press and release the binding button on the bottom of the BGDA. The binding LED should blink fast for two seconds, then blink slowly for 60 seconds. During this 60-second duration, press and release the binding button on the front of the BGCA. It should instantly bind to the BGDA, and the binding LED on both adapters should be solid on. This sets a unique security key for the two adapters to act as a pair and only communicate with each other. For systems with multiple Power Docks, perform the complete binding procedure for each set of adapters before moving to the next to ensure proper binding between pairs. If the system has configured itself properly, the green binding LEDs on the front of the adapters will illuminate. Once the binding procedure is successfully completed between adapters, the BGDA can then be moved to the Power Dock location. Connect iBridge Power Dock Crimp an RJ45 connector to each end of a CAT-5 cable using T568A wiring configuration (max cable length is 50 feet). Plug the BGDA into a live AC outlet near the desired Power Dock location. Make sure the network traffic LED on the front of the BGDA is lit to indicate strong communication between adapters. Program RNET system Follow the RNET system's programming instructions to configure the iBridge Power Dock as a peripheral device type. If the system includes UNO-TS2 touchscreens, use the Screen setup feature in the UNO-TS2 Options menu to set the correct screen template ("iPod (iBridge)") for the Power Dock. Check iPod operation With the RNET system controller and both adapters powered, place an iPod in the Power Dock. The "Docked" LED on the BGDA Dock Adapter and BGCA Controller Adapter should both be solid on. Using an RNET remote control, or the RNET keypad, send a command to the iPod. The iPod should respond to the command, and the activity LED on the BGDA and BGCA should be on and blink periodically. Reset a previously bound BGDA and/or BGCA To reset a previously bound BGDA or BGCA, plug in the unit(s). If the binding LED is on, clear the existing binding by pressing and holding both binding buttons until the binding LED goes off (about 10 seconds). Make sure the network traffic LED is lit to indicate strong communication between adapters. Program audio system Configure the audio system for IR control of the iPod. [. . . ] Pressing the Play key accesses NOW PLAYING, where the >| and |< keys cycle through artist, album, and song title. Pressing Play again accesses SHUFFLE MODE, to select random play of songs or albums or no random play (off ). UNO-TS2 iPod music request screen Russound BGK3 iBridge Power Dock Kit Installation Manual 11 TECHNICAL SPECIFICATIONS BGD2 iBridge Power Dock Dimensions: Weight: iPod connector: Communication port: 4. 72" W x 2. 5" D x 1. 0" H (12. 0 x 6. 4 x 2. 5 cm) 5. 4 oz. (153 g) Standard 30-pin dock connector 5 well adapters 8-pole RJ45 jack (T568A standard) BGCA Power Dock Controller Adapter Dimensions: Weight: Power requirement: OS update port connector: Switch: Communication ports: 5. 69"W x 5. 06"D x 1. 33"H (14. 45 x 12. 85 x 3. 4 cm) 11. 2 oz. (317. 5 g) 100-240 VAC, 50/60 Hz, 0. 1A 4-pole jack for programming cable (Russound P/N 2500-521065) 8-position source/function selector RNET Link In and Link Out (2 8-pole RJ45 jacks, T568A standard) 3. 5mm female jack Pair stereo RCA output jacks HomePlug 1. 0 @ 14Mbps Arkados HomePlug+ @ 28Mbps 56-bit DES encryption 14/28 Mbps 4. 3-20. 9 MHz/2. 1-26. 8 MHz BGDA Power Dock Adapter Dimensions: Weight: Power requirement: Standards: Security: Data transfer rate: Frequency band: Communication port: 2. 83"W x 3. 86"D x 1. 33"H (7. 27 x 9. 9 x 3. 4 cm) 5. 6 oz. [. . . ]