User manual ROSIERES VE 551

[. . . ] It is therefore advisable to ensure the room contains air taps able to ensure a steady flow of fresh air. The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug, read the following instructions; as the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: ­ the wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol [ ], or coloured green or green and yellow; ­ the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black; ­ the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. When making the electrical connections, check that the current socket has a ground connection and that the voltage values correspond to those indicated on the data plate inside the appliance itself. In case your appliance is not furnished with a non separating flexible cable and has no plug, or has not got any other device ensuring omnipolar disconnection from the electricity main, with a contact opening distance of at least 3 mm, such separating device ensuring disconnection from the main must be included in the fixed installation. [. . . ] If your unit features a power lead and plug, position this so the plug is accessible. Always switch off the electricity supply before carrying out any cleaning or servicing operations on the appliance. To clean the inside of the appliance, use a cloth (or brush) dipped in denatured ethyl alcohol. This appliance consists of a hood and a telescopic flues which must be applied to the upper part of the hood in order to cover the draft pipe. 4): this is carried out by pushing the relative catch inwards and turning it downwards until it disengages from the supports. Proceed with these instructions in reverse when refitting the filters. The appliance can be a filtering version one, a ducting version one or with an external motor. USE -------------------------------------------------Avoid using materials which could cause spurts of flame (flambées) near the appliance. When frying, take particular care to prevent oil and grease from catching fire. To avoid possible risks of fire always comply with the indicated instructions when cleaning anti-grease filters and when removing grease deposits from the appliance. Installation with the rear panel The rear metal panel must be fixed to the wall in the upper part of the hob (Fig. Rest the lower edge of the panel behind the hob and fix the upper edge to the wall by means of the two holes in the panel itself, inserting the supplied screws and screw anchors (Fig. The appliance should be fixed to the rear panel in the same way as wall fixing, using the supplied hood brackets and the screws and screw anchors supplied with the panel (Fig. Fixing the telescopic flues The following operations are essential for assembly: ­ Install the wiring system within the telescopic flue. ­ Prepare the air venting hole if your appliance is to be installed in the Ducting version or in the version with an External motor. Using the supplied screws and screw anchors, fix the upper flue bearing bracket to the ceiling and/or wall, checking that it is aligned with the hood (Fig. Ducting version and version with an external motor: ­ Prepare the telescopic flues, remembering that their final position must be that illustrated in Fig. ­ Only as far as the version with an external motor is concerned: electrically connect the hood to the external motor by means of the relative terminal board (Fig. ­ Lift the upper flue and fix it to the bracket by means of the supplied screws (Fig. Pushing it once more the timer which will turn the motor off after 10' is on: the relative led will blink during all this time. [. . . ] Pushing it once more the timer which will turn the motor off after 10' is on: the relative led will blink during all this time. At the end of each working time of 30 hours, all the leds blink at the same time; this indicates that the anti-grease filters need to be cleaned. Once the clean filters are on, push one of the three speed switches to make the count down start again. When using the filtering version of the appliance, the charcoal filters must be changed according to use (Fig. [. . . ]