User manual ROSIERES RLG202IN

[. . . ] Type of gas used Type of burner Air setting By-pass marking (100/mm) Injector Nominal marking heat (100/mm) capacity (kW) Nominal Air necessary Reduced consumpti for combustion nominal heat on m³/h capacity (kW) Reduced Air necessary Nominal consumpti for combustion nominal heat capacity (kW) m³/h on Gas pressure (mbar) Grill electric power (230V 50Hz) Nominal Air necessary Reduced nominal Gas pressure (mbar) consumpti for combustion heat capacity on m³/h (kW) min. Once having unpacked and installed the appliance, take out all the internal accessories and bring the oven to the maximum temperature for a 20 minutes time, in order to eliminate any remains of manufacturing grease , oil or resins that can produce unpleasant smells during cooking. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. [. . . ] Using an attachment without seals (the oven attachment is conical: ISO R 7). Use soap and water or special liquids to make sure that there are no gas leaks. The use of a rubber flexible hose fastened with hose clamps is prohibited because it cannot be inspected. Other types of gas can be used by changing the burner setting as follows: 1) Make sure that the oven is not connected to the electrical mains. 3) Extract the bottom of the oven after having removed the retaining screws (fig. Reassemble the burner and the bottom of the oven, following the above steps in the reverse order. To adjust the flame, proceed as follows: loosen the screw C and turn the ring nut D to position for natural or methane gas, and position for cylinder gas, aligning the movable pointer on the ring nut with the fixed pointer on the burner. The oven thermostat is equipped with a by-pass for the minimum; when changing the type of gas it is also necessary to adjust the setting in the following manner: Remove the thermostat knob; If the front panel is in glass, remove it by unscrewing the two locking ring nuts located under the other two knobs (fig. 7a); If the control panel is in metal, the adjustment can be made through the opening located on the left side of the thermostat knob housing (fig. 7b); Turn on the oven and let it operate at maximum with the door closed for at least 30 minutes; Move the oven thermostat knob to the minimum and set the by-pass to the minimum so as to obtain a reduced but stabilized flame. Perform this operation with the oven door closed; Use a screwdriver to operate on the notch of the by-pass screw. A few turns of the by-pass screw is sufficient to adjust the minimum when passing from liquid gas to methane gas; After having adjusted the burner, open and close the oven door to check that the flame remains lit at the minimum. For operation with G30/G31, the adjustment screw of the by-pass must be screwed in completely. When these operations are finished (injector replacement, air adjustment and minimum setting), turn off the oven and replace the data plate with the new data plate indicating the operating gas. Use: the oven burner has a safety valve which block the gas flow in the following cases: - If the thermostat knob is accidentally turned with immediate gas flow. The green light turns on when the selector knob is in any position different from 0. It is recommended to keep the oven door open and to use the knob protection. If the thermostat knob is turned accidentally during electric grill operation, a safety device will stop the grill. To restart, rotate the knob until the mark on the knob is aligned with the mark on the control panel. By turning the knob anticlockwise the temperature can be selected between 150°C and Max. [. . . ] Wash accessories in a dishwasher or by hand using a product for oven cleaning. 8) To make it easier to clean the oven, it is possible to remove the door from the hinges as follows: The hinges A are equipped with 2 mobile U -bolts B. When the U-bolts B are lifted, the hinges are disconnected from their housing. After this, lift the door up and pull it outwards, holding the door on both sides near the hinges. [. . . ]