User manual ROSIERES RDH32

[. . . ] The “+” and “” controls (4) are common to both functions. Accordingly, to regulate the power of the hob, first select the zone with key (2), then adjust the relative power level using the “+” and “-” keys (4); this done, select the timer function with key (5) and proceed to set the duration, likewise using the “+” or “-” key (4). 1- Press and hold down these keys to increase or decrease the setting. Tion de la : 1– Press and hold down these keys to increase Switching offsetting. [. . . ] IT After a time interval, the power level automatically returns to GB the original setting. En préchauffage without the function hu- cuisson est à chauffer au cottura inizierà a riscaldare preheating need 5. Se nessuna zona viene esplicitamente 510 Select function too simThis the required cooking area by means of the150 (2). Plifies operation key by Select power level 9 210 by not requiring human means of key “+” (4), then supervision during 270 presscooking cycle. On Once the set time The lettertimer has elapsed, the “A” will be shown on the relative display. Spontaneous movement the automatic towards the required preheating function (inpower level (e. €5”), dicated by the letter set the power to 5 by GB “A”). To preheat the unit with After the system the Switching offhas set spontaneous movement to automatic preheating automatic towards the required mode, the display panel preheating funcpower level (e. €5”), will alternate the set tion set the level (“5”) and power power to 5 by means of the the thedeactivate “-” key (4). Select the cooking on the willthat key (4)theleast 10 zone “-” has this function active the alternate at set (brighter display)(“5”) funcpower level and then Switching off and seconds since to the touchautomatic thelower the the “-” key (4) automatic activated. The cookingbeenThis must(inpreheating function be preheating and done within 10 the funcseconds, dicated letter tion by deactivates the function. To deactivate the Switching off the preheating function (inautomatic letter “A” dicated by the preheating funcon the display), press tion key (4) at least the “-” Heat maintenance 10 seconds since the funcfunction To deactivate the tion has function Timer been activated. Preheating function (indicated by between 1 and 0 A heating level the letter “A” This function too simis anthe display), press on intermediate power by plifies operation level displayed key the symbol “u”10 the “-” with (4) at least not requiring human and serves to maintain the heat; seconds sinceduring supervision the funcit is activated by pressing the “+” tion cooking cycle. Once the set time on the timer has elapsed, the cooking area is auTimer function tomatically switched off. If no zone has This function too simbeen programmed, plifies operation by the timer simply opernot requiring human ates as a minute counsupervisionsection ter (see the during Timer functionas a the cookingtimer “Using the cycle. This function elapsed, the timer has too simplifies operation byauthe cooking area is not requiring human tomatically switched supervision during off. Been programmed, Once the set timeoperthe timer simply on the as a has elapsed, atestimerminute counthe cooking area is ter (see the section automatically timer as a “Using the switched off. Been programmed, the timer simply operates as a minute counter (see the section “Using the timer as a minute counter”). IT IT Using the timer Using the timer function function 1 - The cooking zone must be activated, therefore, brighter. 3 - Touch the timer key (5): The timer will display “00” and the decimal point of the cooking zone will flash (9); 4. Select the cooking time (between 0 to 99 minutes) by means of the “+” and “-” keys (4). Press and hold down the “+” or “-” key (4) to scroll the time setting. [. . . ] The appliance is not intended for use with an external timer or a separate remote control system. The appliance can be fitted into a working area as illustrated on the figure. 6) Prior to carrying out the electrical connection, please ensure that: - the plant characteristics are such as to follow what is indicated on the matrix plate placed at the bottom of the working area; - that the plant is fitted with an efficient earth connection, following the standards and law provisions in force. Should there be no cable and/or plug on the equipment, use suitable absorption material for the working temperature as well, as indicated on the matrix plate. [. . . ]