User manual ROSIERES RBS 94

[. . . ] - This device must be connected to the supply network through either a plug fused 3A or hardwired to a 2 fase spur protected by 3A fuse. A) Do not check the status of the filters while the cooker hood is operating B) Do not touch bulbs or adjacent areas, during or straight after prolonged use of the lighting installation. C) Flambè cooking is prohibited underneath the cooker hood D) Avoid free flame, as it is damaging for the filters and a fire hazard E) Constantly check food frying to avoid that the overheated oil may become a fire hazard F) Disconnec t the elec trical plug prior to any maintenance. G) This appliance is not intended for use by young children or infirm persons without supervision H) Young children should be supervised to ensure they do not play with the appliance I) There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances burning gas or other fuels L) There is a risk of fire if cleaning is not carried out in accordance with the instructions This appliance conforms to the European Directive EC/2002/96, Assembly and electrical connections must be carried out by specialised personnel. [. . . ] Fixing the decorative telescopic flue - extractor version Arrange the electrical power supply within the dimensions of the decorative flue. If your appliance must be installed as an extractor version, make sure an air exhaust hole has been prepared. 3) in such a way that it is in line with your hood and respecting the distance from the ceiling indicated in Fig. 4), extract the upper flue up to the bracket and fix it with the screws B (Fig. To transform the hood from a ducting version into a filtering version, ask your dealer for the charcoal filters and follow the installation instructions. If the cooker hood is at speed level 1 it will not be necessary to depress the push-button to switch the cooker hood off. Touching the key at 3rd speed, the intensive function runs for 10', then the appliance go back to work at the original speed. Key E = The Timer times the functions on activation for 15 minutes, after which they are switched off. When the Timer is activated the decimal point must flash on the display. The "clean air" function is activated by pressing key E for 2 seconds when the appliance is switched off. This switches the motor on for 10 minutes every hour at the first speed. During functioning a rotary movement of the peripheral segments must be visualised on the display. When this time has passed the motor switches off and the fixed letter "C" must be visualised on the display until the motor re-starts after 50 minutes for another 10 minutes and so on. Press any key apart from the light keys to return to normal functioning. Active carbon/grease filter saturation: - When display item C flashes, at a speed where it alternates with the letter F (e. - When display item C flashes, at a speed where it alternates with the letter A (e. After the clean filter has been positioned correctly, the electronic memory must be reset by pressing button A for approximately 5 seconds, until the indication F or A shown on the display C stops flashing. 9 A) luminous the key symbols are explained below: A = LIGHT B = OFF C = SPEED I D = SPEED II E = SPEED III F = AUTOMATIC STOP TIMER - 15 minutes · By pressing key F for two seconds (with the hood switched off ) the "clean air" function is activated. This function switches the appliance on for ten minutes every hour at the first speed. As soon as this function is activated the motor starts up at the first speed for ten minutes, During this time key F and key C must flash at the same time. After ten minutes the motor switches off and the LED of key F remains switched on with a fixed light until the motor starts up again at the first speed after fifty minutes and keys F and C start to flash again for ten minutes and so on. By pressing any key for the exclusion of the hood light the hood will return immediately to its normal functioning (e. [. . . ] After the clean filter has been replaced, the electronic memory must be reset by pressing button A for approximately 5 seconds, until the light on the button stops flashing. 9 B) mechanical the key symbols are explained below: A = LIGHT B = OFF C = SPEED I D = SPEED II E = SPEED III G = MOTOR WORKING indicator · To replace the halogen light bulbs B, remove the glass pane C using a lever action on the relevant cracks. To remove the incandescent light bulb, take out the grease filters as described in (Fig. CUSTOMER ASSISTANCE SERVICE Before contacting the Technical Assistance Service: If the product does not operate at all, we advise you to: - check that the plug has been inserted into the power socket correctly. [. . . ]