User manual ROSIERES PG90

[. . . ] This appliance complies with the following European Directives: - 2006/95/EEC regarding "Low Voltage". - 90/396/EEC regarding “Gas appliances” - 89/109/EEC regarding "Materials in contact with food" - Moreover the above mentioned Directives comply with Directive 93/68/EEC. This appliance must be installed in accordance with the regulations in force and must only be used in well ventilated rooms. Consult the instructions booklet before installing and using the appliance. [. . . ] Cooking time and manual function = saucepan symbol Automatic function = AUTO Minutes counter = bell symbol The symbols light up when the corresponding functions are selected. Minute timer A U T O Minutes counter Press the minutes counter button and set the cooking time with or button. The bell symbol lights up when the minutes counter is operating When the set time is up, the sound signal rings and the bell symbol switches off. Sound signal The sound signal starts at the end of a programme or of the minutes counter function and it lasts for 15 minutes. oven accessories optional A 33 5 m B m 4 0 5 m m A = wire shelves B = Grill pan set (2) 4 GB INSTRUCTIONS FOR USE OF CONTROL DEVICES “LED” PROGRAMMER (Fig. When the cooking time is up, the AUTO symbol flashes, the sound signal rings and both the relay and the cooking time button switch off. Automatic use with cooking time and end time setting Press the cooking time button and select the length of the cooking time with or button. By pressing the cooking end time button the next cooking end time appears on the display. The symbol lights up again when the time of day corresponds to the cooking start time. When the cooking time is up, the AUTO symbol flashes, the sound signal rings, the cooking time symbol and the relay switch off. CARE AND MAINTENANCE Before cleaning the appliance, disconnect the gas general tap and unplug the appliance or disconnect power at the main circuit breaker of the electrical system. IMPORTANT Periodically check the external gas connection hole and replace it when it shows any sign of deterioration. Grease can be easily removed using hot water or a specific cleansing agent for enamelled surfaces. Do not leave any acid or alkaline substances (lemon juice, vinegar, salt, etc. Clean the parts in stainless steel with specific cleansers for stainless steel surfaces. GRIDS AND BURNERS To clean the work-top burners, remove them by pulling upwards and soak them for about 10 minutes in hot water with a little detergent. OVEN Clean the enamelled parts with a damp sponge using soap and water. Grease can be easily removed using hot water or a specific cleansing agent for enamelled surfaces. The interior glass of the oven The interior glass of the oven door can be removed: with the door in a semi-open position, remove the screws A and B and the profime C as shown in fig. 5 GB B A C INSTRUCTIONS DESTINED TO THE USER OVERALL DIMENSIONS Fig. 9 Removal of oven door In-depth cleaning of the oven becomes more convenient if the door is removed following the instructions below: 1 open the oven door completely. 3 shut the oven door slowly until it reaches hooks "A", making sure these are locked into slots "B" of the oven door, as shown in fig. [. . . ] Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel. 3, 00 1, 75 1, 00 3, 30 0, 75 219 g/h 55 g/h 42 0, 48 128 g/h 35 g/h 31 0, 33 73 g/h 24 g/h 27 1, 30 241 g/h 95 g/h 60 MINIMUM FLOW ADJUSTMENT FOR WORK-TOP TAPS In order to adjust the minimum, act as follows: switch the burner on, and turn the knob towards the minimum flow position . Remove the knob from the tap, introduce a little screwdriver in the tap rod (fig. Attention: in taps with security valve, the minimum adjusting screw “Z” is placed outside the rod tap (fig. [. . . ]