User manual ROSIERES PCDVE2CPN

[. . . ] Drill as shown (6 holes for 6 wall plugs ­ 4 plugs for fixture), screw the outer screws leaving a space of about 1 cm. Fit an exhaust pipe inside the truss and connect it to the motor compartment connection ring (exhaust pipe and fixing brackets 11 are not supplied). The side of the truss with connection box corresponds to the side of the control panel with hood assembled. Insert and tighten another 2 screws in the remaining free holes for secure fixing. [. . . ] Hook the hood onto the truss, ensuring it fits properly ­ to hook the hood onto the truss partially tighten 4 screws (see also step 12). Secure the hood to the truss using two screws; this will also help center the two sections. For filter versions (13F), fit deflector F to the truss and secure it to the bracket supplied using 4 screws, then connect the exhaust pipe to the connection ring located on the deflector. Fit the nuts with fixing hooks supplied inside the top and bottom sections of the flues at the rectangular slots. Join the two top sections of the flue to cover the truss so that one of the slots on the sections is situated on the same side of the control panel and the other on the opposite side. Screw the two sections together with 4 screws (2 each side- see the plan diagram for joining the two sections). Fix the top flue assembly to the truss, near the ceiling, with two screws (one each side). Make connections taking care to insert the connectors in the right way. Join the two bottom sections of the flue covering the truss using 6 screws (3 each side, see the plan diagram for joining the two sections). Insert the bottom section of the flue in its seat so that it completely covers the motor compartment and electrical connection box, then ensure it from inside the hood using two screws. Apply the 2 tabs (supplied) to cover the fixing points of the bottom flue (CAUTION!Grease filter This must be cleaned once a month (and, for the model with electronic control panel, every time LED 4 starts to flash ­ see preceding page) using non aggressive detergents, either by hand or in the dish-washer, which must be set to a low temperature and a short cycle. When washed in a dish-washer, the grease filter may discolour slightly, but this does not affect its filtering capacity. To remove the grease filter, pull the spring release handle (f) - (Fig. Only for model with electronic control panel: Once the grease filters have been cleaned, press button 1 (see preceding page) for about 3 seconds until you hear the acoustic signal (beep): the LED 4 will now stop flashing. charcoal filter (filter version only) It absorbs unpleasant odours caused by cooking. The charcoal filter can be washed once every two months (when using the hood 2, 5 hours per day, in avarage and, for the model with electronic control panel, every time LED 5 starts to flash ­ see preceding page) using hot water and a suitable detergent, or in a dish-washer at 65°C (if the dish-washer is used, select the full cycle function and leave dishes out). Eliminate excess water without damaging the filter, then remove the mattress located inside the plastic frame and put it in the oven for 10 minutes at 100° C to dry completely. Insert the pad (i) of activated carbon into the frame (h) and fit the whole back into its housing (j). Only for model with electronic control panel: Once you have replaced the charcoal filter, press button 1 (see preceding page) for about 3 seconds until you hear the acoustic signal (beep). Only use halogen bulbs of 20W max (G4), making sure you do not touch them with your hands. Extract the guard by levering it off with a small screwdriver or similar tool. [. . . ] Extract the guard by levering it off with a small screwdriver or similar tool. Only use halogen bulbs of 20W max (G4), making sure you do not touch them with your hands. Use a small screwdriver as a lever on the borders of the lamp in order to remove the lightbulb. Slide out the lightbulb to be replaced and replace with a new 12V 20W 30° Ø35 12V GU4 PHILIPS STANDARD LINE code 425409. [. . . ]