User manual ROSIERES LV 522

[. . . ] RECOMMENDATION : When the burners are not being used the mains gas supply valve should be closed. THE RAPID DOUBLE RING BURNER 3, 2 kW 3200 watts utilised on two burner rings of flames which ensure a best heat dissipation on the pan base. Use the large burner for bringing to the boil, for cooking large quantities, and generally for all foods requiring rapid cooking. To make the most efficient use of the burners, it is recommended not to use pans with smaller diameters than shown below : * Ultra-rapid Ø 20 cm and more * Rapid Ø from 16 to 18 cm * Semi-rapid Ø 12 cm Pans with curved, ridged or warped bottoms are not recommended. [. . . ] To save gas, make sure that the flames do not overlap the bottom of the pan. To remove stubborn stains use a spot of non-abrasive cream and a sponge and then rinse with clean water. regular cleaning is essential to maintain the original appearance of the appliance. Do not immerse the burner caps or burner support in cold water immediately after use to avoid cracking the enamel from the thermal shock. The use of abrasive cleansers is not recommended as they scratch and dull the enamel. If the holes are clogged, brush the caps using soapy water and dry with a clean cloth. The burner support : regular cleaning enables you to keep the original appearance. When re-assembling the burners, make sure that the burner caps and the burners themselves are correctly seated. When re-fitting the caps, make sure that the recess is fitted correctly into the projection. THE CONTROL KNOBS : For thorough cleaning, the control knobs can be removed by pulling them upwards. GAS CONNECTION - It must be carried out in accordance with the regulations in force in the country of use. However, in all circumstances the gas supply pipe should be fitted with a stop tap, a pressure regulator or a pressure reducer release valve for LPG. The stop tap, pressure regulator or pressure reducer release valve should only be used in accordance with the regulations in force in the country of use. BUILD-IN HOB : Butane gas Rigid hose - Flexible hose with mechanical nozzles (1) Propane gas Rigid hose - Flexible hose with mechanical nozzles (1) Natural gas Rigid hose - Flexible hose with mechanical nozzles (1) (1) The connection must be made in such a way that the flexible hose must never be in contact with hot parts of the appliance and must be placed in such a way to be examinable on all its length. If the hob is to work with another type of gas, the appliance must be adapted accordingly ; to do this, proceed as follows : - put the proper injector in (which will insure a normal flow), - regulate the air flow, and, - regulate the minimum flow. HOB INJECTORS : - Remove the pan supports and the burners, - Unscrew the injectors, using the special key (supplied with the appliance), - and replace the injector with ones specially designed to operate with the new type of gas (see page 10). REGULATION OF THE AIR FLOW : When necessary (see the table) this regulation is very important because it obtains proper combustion and the best efficiency of the burners. The chart mentionned the theorical size "X", it can be necessary to improve the setting in a more or less 1 mm in order to get a perfect flame. With a A screwdriver (Ø 2 maxi), act on the setting screw of the tap, clockwise to increase the gas, and anti-clockwise to decrease the gas, till you get a flame of 3 to 4 mm remaining stable when going from high flame to low flame. Rosières declines all responsability for any damage that may be caused by unsuitable or unreasonable use. [. . . ] Rosières declines all responsability for any damage that may be caused by unsuitable or unreasonable use. Connection to the mains electricity supply should be through a plug with an earth terminal, or through an omnipolar switch, contact or cut-out, with a gap between the contacts of at least 3 mm. the electrical installation should be protected by a fuse , properly earthed , and including wires of a sufficient section to supply the product correctly. This appliance is supplied with a cord and plug which is only suitable for connection to a power supply of 220-240 V~ between the 2 phases or one phase and neutral. [. . . ]