User manual ROSIERES F 254

[. . . ] ­ If your unit is installed in an Exhaust hood or in a hood with outside motor, prepare the air exhaust hole. When installing exhaust hoods and hoods with outside motor, to achieve the best possible conditions use an air exhaust pipe that: is as short as possible, has a minimum of curves (maximum angle: 90°), is made of a material that complies with the standards (which vary from nation to nation) and iv) is smooth on the inside. It is also advisable to avoid any drastic changes in pipe section (diameter: 150 mm). Adjust the width of the extension pipe support bracket (W) using screws A indicated in Fig. [. . . ] Insert the extension pipes setting them on the hood; extend the upper pipe to the ceiling and secure with the 2 screws (G) (Fig. Filtering hood: Secure the deflector to the upper pipe using the 4 special screws (provided) (Fig. Take the 2 assembled extension pipes and set them on the hood; extend the upper pipe to the ceiling and secure with the 2 screws (G) (Fig. Extend the lower pipe taping it in place and then connect the flexible pipe to the hood reduction. Install the carbon filter by pressing the 2 tabs on the filter down into the special housing (Fig. Depending on the model, the unit is equipped with the following commands: CONTROLS shown in Fig. 14: P1 Switches LIGHTS on and off P2 min and MAX LIGHT intensity P3 Nothing happens when pressed with motor OFF. Kept pressed for 2" with motor OPERATING, switches off motor and stores the speed. P4 When pressed with motor OFF, switches on the motor at stored speed in switch-off or first speed phase When pressed with motor ON, increases speed. L1 and shows current speed (GREEN) P5 Resets filter reset count with motor OFF. L2 Shows: 1) with motor off, the FILTER RESET IN RED, (30hours Steady LED, 120hours flashing LED) 2) In FLASHING GREEN the TIMER 5' CONTROLS shown in Fig. The air collected must not be conveyed into a duct used to blow off smokes from appliances fed with an energy other than electricity (central heating systems, thermosiphons, water-heaters, etc. Comply with the official instructions provided by the competent authorities in merit when installing the disposal duct. In addition, exhaust air should not be discharged into a wall cavity, unless the cavity is designed for that purpose. The room must be well aerated in case a hood and some other heat equipment fed with an energy other than electricity (gas, oil, coal heaters, etc) operate at the same time. In fact the intake hood, disposing of air, could create a vacuum in the room. This prevents the gas exhausted by the heat source from being intaken again. It is therefore advisable to ensure the room contains air taps able to ensure a steady flow of fresh air. Check the data label inside the appliance; if the symbol ( ) is printed, read the following: this appliance has such technical particulars that it belongs to class II insulation, therefore it must not be earthed. The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug, read the following instructions; as the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: ­ the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black; ­ the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Check the data label inside the appliance; if the symbol ) is NOT printed, read the following: ATTENTION: ( This appliance must be earthed. When making the electrical connections, check that the current socket has a ground connection. [. . . ] The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug, read the following instructions; as the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: ­ the wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the ], or coloured green or letter E or by the earth symbol [ green and yellow; ­ the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black; ­ the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. When making the electrical connections, check that the voltage values correspond to those indicated on the data plate inside the appliance itself. In case your appliance is not furnished with a non separating flexible cable and has no plug, or has not got any other device ensuring omnipolar disconnection from the electricity main, with a contact opening distance of at least 3 mm, such separating device ensuring disconnection from the main must be included in the fixed installation. If your unit features a power lead and plug, position this so the plug is accessible. [. . . ]