User manual ROSIERES 4015 RU

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ROSIERES 4015 RU. We hope that this ROSIERES 4015 RU user guide will be useful to you.


ROSIERES 4015 RU : Download the complete user guide (3125 Ko)

Manual abstract: user guide ROSIERES 4015 RU

Detailed instructions for use are in the User's Guide.

[. . . ] Also, make sure that the flexible pipe cannot come into contact with a moving part of the cabinet (eg, a drawer) and that it is not situated where it could be damaged. For some models a conic link is furnished to outfit for the installation in the countries where this type of link is obligatory; in the following figures it is pointed out how to recognize the different types of links. Warning : before proceeding with the connection, check the continuity of the earthing of the power supply unit. We cannot be held responsible for any accident which has resulting from the use of an appliance which is not connected to earth, or whose earthing is defective. [. . . ] The air ring is located at the lengthening of the burner unit which is fixed by a screw (see drawing). Set the correct distance according to the air adjuster protrudes, · Fixing screw Fixing Air screw regulation If you have changed the type of gas, it is important to verify the flame stability at the minimum regulation. Turn the control knob from minimum to maximum position to check that it is satisfactory. B) Butane-propane gas : The by-pass screw should be screwed fully home, without being locked. If they are to be used with another type of gas, the appliance must be adjusted in the following way: Fit the correct jet for the type of gas to be used, · If you have changed the type of gas, it is important to verify the flame stability at the minimum regulation. Turn the control knob from minimum to maximum position to check that it is satisfactory. B) Butane-propane gas : The by-pass screw should be screwed fully home, without being locked. Each burner is contolled by a tap with progressive settings allowing: * a wider choice of settings from the maximum position to the lowest and most precise one, * easier flame regulation according to the pan diameter, * no risk of cutting off the flame or switching off when the flame is turned down quickly. IGNITION RECOMMENDATIONS : when the burners are not in service, the general gas supply tap should always be turned off. Turn and press in the relevant burner control knob to the "+" ( ) symbol, keeping it pressed in until the flame ignites. on models fitted with electronic ignition the flame is ignited by an electric spark. To save gas, make sure that the flames do not overlap the bottom of the pan. To get the best results from your appliance it is important to observe the following : · Use thick, flat-based cooking vessel : a completely flat base prevents overheating to certain parts which causes food to stick. Make sure that the base of the pan is dry : this will prevent sticking to the hot plate caused by moisture. Use pans with a diameter large enough to completely cover the hot plate, otherwise energy will be wasted and any spillages will cause the hot plate to become stained and will become difficult to maintain (rust, etc. Never leave a hot plate switched on without a pan on it : it can be damaged, which would reduce its efficiency. When cooking with fat or oil, never leave the hob unattented, very hot fats and oils can quickly catch fire. When the hot plate is hot, avoid any contact with materials made of plastic or aluminium foil. Caution : the heating surfaces clearly get hot while operating, so make sure that small children are kept well away from the hob. Never use : harsh abrasives, scouring pads or sharp objects to clean the hob. ENAMELLED STEEL HOB: when the hob has cooled completely, simply clean the enamelled hob with soapy water, rinse and wipe with a clean dry cloth. You can use a special product to clean stainless steel which is available from various retail outlets. [. . . ] The brass finish burner cap: on using, the burner cap surface looses its brightness. For current cleaning, it is recommended to remove all greasy or burnt deposits with ammoniacal products or usual cleaning products. To recove brass brightness, use a special cleaning product for copper, brass or bronze currently sold in stores. If the holes become clogged, brush the caps using soapy water and dry with a clean cloth. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ROSIERES 4015 RU




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ROSIERES 4015 RU will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.