User manual ROBLIN IKOS 600 DIMENSIONS

[. . . ] 04 mbar to prevent the fumes from combustion being drawn back into the room. The appliance is for domestic use only and should not be operated by children or people who are infirm without supervision. This appliance must be positioned so that the wall socket is accessible. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. [. . . ] The X measurement may have different values, according to the available heights of the upper chimney stack. 1 & 2): Mark a point on the vertical line at a distance from the cooking appliances of: d = 945 mm (Measurement without splashback). The distance H is the minimum height in mm from the cooking appliances to the bottom edge item 3 of the front panel of the hood. At the point marked, draw a horizontal line parallel to the cooking appliances. Drill two holes 1 in the wall using an 8 mm drill bit and insert the rawl plugs and screws into the holes 1 (4. Fix the screws, leaving a space of 5-6 mm required to hook up the canopy (Fig. Small adjustments can be made using the hood adjustment screws (see Fitting the canopy). Splashback (optional): When a splashback is to be fitted, the distance between the hood and the cooking appliances will be determined by the height of the splashback item B and whether or not there is a raised back on the worktop. If the splashback is to be fixed to the wall using both the top and bottom fixing holes, Care must be taken to ensure that the splashback is fitted at the correct height before fixing the base units or at least the worktop covering them. As this is a complex operation, it should only be undertaken by the technician installing the kitchen units or by a competent person who knows the final dimensions of the units. 4) Fixing the canopy: Before starting to fix the canopy it will be necessary to adjust the support brackets by turning the adjustment screws Vr in a clockwise direction until their reach their limit (Fig. 4 OPERATION Key Key Key Key 1 2 3 : : : : low speed medium speed high speed lighting To obtain the best performance we recommend you to switch `ON' the cooker hood a few minutes (in the boost setting) before you start cooking and you should leave it running for approximately 15 minutes after finishing. IMPORTANT: NEVER DO FLAMBÉ COOKING UNDER THIS COOKER HOOD Do not leave frying pans unattended during use as over-heated fat and oil might catch fire. switch `OFF' the electric and gas before removing pots and pans. Ensure heating areas on your hotplate are covered with pots and pans when using the hotplate Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean; a build up of fat or grease may cause a fire hazard. casing · Wipe the cooker hood frequently with a clean cloth, which has been immersed in warm water containing a mild detergent and wrung out. Never use excessive amounts of water when cleaning particularly around the control panel. Metal Grease Filters : The metal grease filters absorb grease and dust during cooking in order to keep clean the cooker hood inside. The grease filters should be cleaned once a month or more frequently if the hood is used for more than 3 hours per day. The filter should be replaced at least every three months or more frequently if the hood is used for more than three hours per day. Press against the two retaining clips, which hold the charcoal filter in place and this will allow the filter to drop down and be removed. [. . . ] This Guarantee does not cover : - Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or filters or removable parts of glass or plastic. These items are considered to be consumable under the terms of this guarantee. This appliance complies with European regulations on low voltages Directive 2006/95/CE on electrical safety, and with the following European regulations: Directive 2004/108/CE on electromagnetic compatibility and Directive 93/68 on EC marking. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European directive 2002/96/EC. [. . . ]