User manual PYRAMID PW855US-X DATASHEET

[. . . ] shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from improper use of this product. Please read the following items before use This Case is a precision device designed for use at a water depth within 40 m. Please use the Case correctly after sufficient understanding of the contents of this manual in regard to handling of the Case, checks before use, maintenance, and storage after use. shall in no way be responsible for accidents involving immersion of a digital camera in water. In addition, expenses incurred for damage of internal materials or loss of recorded contents due to water entering the camera will not be compensated. [. . . ] 21 Underwater shooting modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 How to select the shooting scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Locking AF during underwater shooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handling After Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Wipe off any waterdrop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Take out the digital camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Wash the Case with pure water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Dry the Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Remove the O-ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 EN 6 How to Apply Grease to the O-ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Install the O-ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Replace consumable parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 7. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . · Check if the correct mode is being switched from the LCD monitor. 3 Press the shutter lever on the Case and confirm that the camera shutter releases. · Also operate other control buttons on the Case and confirm that the camera functions properly. EN 18 Perform the final checks Visual Inspection After sealing the Case, check the sealing part of front and rear lid visually to confirm that the O-ring is not twisted or out of the groove and that no foreign matter has been caught. CAUTION: Hairs, fibers, and other narrow items are not very apparent, but they may cause water leakage. In addition, pay special attention to breaks and cracks on the Case. En EN 19 Water Leakage Test The final test after loading the camera is explained below. The required time is about five minutes. En 1 Simple water leakage test Place the Case slowly into the water. Explanatory image Hints As the Case is transparent, waterdrops entering into it can be confirmed easily. In case of trouble with the O-ring, three seconds are enough for water to enter. Remove the Case from the water and check that no water has leaked at the inside of the Case. 2 At first, immerse the Case for only three seconds. 3 Check that no water has entered into the Case. 4 Next, immerse the Case for 30 seconds. Check carefully for air bubbles!Remove the Case from the water and check that no water has leaked at the inside of the Case. Perform very careful confirmation. 5 Check that no water has entered into the Case. 6 Next, check by immersing for three minutes. Check carefully for air bubbles!Has the silica gel become moist? 8 Now everything is all right. Now everything is all right! EN 20 4. [. . . ] · Operate the shutter lever and various buttons of this product in pure water to remove salt adhering to the shaft. Always wash off any salt after use. Dry the Case After washing with pure water, use a clean cloth to wipe off any waterdrops. Be sure to use a cloth free of salt residue that doesn't leave any loose fibers. CAUTION: · Do not use hot air from a hair dryer or the like for drying and do not expose the Case to direct sunlight, as this may accelerate deterioration and deformation of the Case and deterioration of the O-ring, leading to leakage of water. [. . . ]