User manual PURE ELAN II

[. . . ] C A B Wait for Élan II to complete an Autotune, which finds all available DAB stations (this takes about a minute). (See page 10) 1 2 Getting started Controls at a glance Standby Switch on and into standby (off if ChargePAK fitted) Presets 1-5+ Store up to 50 DAB or FM preset stations ReVu Press to pause and play live DAB radio. Press and hold to return to live radio DAB/FM/AUX Switch between DAB/FM/AUX source Standby DAB/FM/AUX 1 2 3 4 5+ Bass/Treble ReVu Menu Alarm/Timer Volume Tune Volume Rotate dial to adjust volume. Menu Access radio setup options Tune Rotate to tune and navigate menus, push to confirm selections Alarm/Timer Set the alarm, kitchen timer or sleep timer EN Bass/Treble Adjust audio settings Rear connectors USB connector for software upgrades (mini-B type). [. . . ] Tune Tune Tune Tune To cancel a kitchen timer To stop and reset the kitchen timer before it sounds a beeping tone, press and hold down the Alarm/Timer button for two seconds until you see the message ‘Timer cleared’. 2 Alarm/Timer Setting the sleep timer Élan II has a sleep timer that switches your radio into standby (or off if powered by a ChargePAK or batteries) after a number of minutes has elapsed. Press the Alarm/Timer button, rotate the Tune dial to display Sleep timer then push the Tune dial to select. Rotate the Tune dial to increase the duration of the sleep from 15 to 90 minutes in fifteen minute intervals. Tune Tune To cancel a sleep timer Select the Sleep timer screen (see above) and set the duration of the Sleep timer to Sleep Off. Alternatively, press and hold the Alarm/Timer button for three seconds until you see the message ‘Timer cleared’. 8 Setting the alarm & timers Options and settings Press the Menu button to access the options menu, rotate the Tune dial to scroll through and change the options and push to select. DAB options Autotune Scans all DAB Band III frequencies for stations, automatically adds any new stations found to the station list and removes inactive stations. Intellitext options Select ‘Intellitext’ and use the Tune dial to access the following options for managing Intellitext messages: Set timeout Choose to delete old Intellitext messages after 1 week (default) or 1 day. FM options FM tuning mode Seek Manual When you rotate the Tune dial, the radio tunes to the next station with a good signal. When you rotate the Tune dial, the radio tunes up or down in steps of 0. EN General options Backlight Timed Off On The backlight turns on for 7 seconds when any button is pressed (default). Audio Push the Tune dial to select, then rotate to adjust the treble or bass and push to confirm. Treble Adjust the treble between -5 (minimal treble), and 5 (high treble). Clock The clock will automatically set itself and also update for GMT/BST clock changes. However, if you cannot receive a DAB signal, the time and date can be manually set by selecting Set Clock from the options menu. Options and settings 9 Energy saving Élan II is part of the PURE EcoPlus product family, designed and manufactured to minimize power consumption when the unit is switched on and to use less than 1 Watt in standby. One way this low power consumption is enabled is by not collecting and storing Intellitext messages when the unit is in standby. Two options are available: On (default) Élan II updates the Intellitext data when you tune to a station that broadcasts Intellitext. Off Élan II collects Intellitext data in standby from the last station you used to view Intellitext. Note: If you fit the optional ChargePAK C6L or 6 x ‘C’ cell batteries (see below), your radio will switch off when you press the Standby button and not enter standby, as long as it is not connected to mains power. Software upgrade Software updates for your Élan II may be made available in the future. [. . . ] Hvis en station tilbyder sekundære tjenester, vises det i stationsoversigten med ‘>>’ ud for stationens navn i stationslisten, og den sekundære tjeneste vises ud for den pågældende station i oversigten. Warrants to the end user that this product will be free from defects in materials and workmanship in the course of normal use for a period of two years from the date of purchase. This guarantee covers breakdowns due to manufacturing or design faults; it does not apply in cases such as accidental damage, however caused, wear and tear, negligence, adjustment, modification or repair not authorised by us. Should you have a problem with your unit please contact your supplier or contact PURE Support at the address shown on the rear of this manual. [. . . ]