User manual PUNCH! SOFTWARE INTERIOR DESIGN SUITE V10 V1

[. . . ] This document, as well as the software described in it, is furnished under license and can only be used or copied in accordance with the terms of the license. Portions of the software described in this document © 1995-2005 Microsoft Corporation. Except as permitted by such license, no part of this document can be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Punch!reserves the right to improve, enhance and revise its products without notice. [. . . ] Each click will increase (or decrease) the dimension by the set increment. Note: The current measurement is always displayed next to the incremental arrows. To change the toe kick dimension 1 On the Standard toolbar, click the Toe Kick tool or, on the Size menu, click Toe Kick Size. The stile width changes to reflect the new measurement. To change the stile width by set increments 2 3 Type the toe kick size in the text box. The toe kick dimensions change to reflect the new measurement. On the Standard toolbar, click the up or down arrow next to the Stile Width Tool. Each click will increase (or decrease) the dimension by the set increment. Note: The current measurement is always displayed next to the incremental arrows. To change the door height 1 On the Standard toolbar, click the Door Height tool or, on the Size menu, click Door Height. The Door Height dialog box is displayed. To change the toe kick by set increments On the Standard toolbar, click the up or down arrow next to the Toe Kick Tool. Each click will increase (or decrease) the dimension by the set increment. 162 PUNCH!Interior Design Suite User's Guide Moving around in Cabinet Wizard To view your design using Fly-Around 1 2 3 On the View menu, click 3D Viewing Method> Fly-Around, or click the Fly-Around button on the Cabinet Wizard window. Move the Fly-Around pointer around inside the Cabinet Wizard window and watch the view move dynamically. Type the door height in the text box. The door height changes to reflect the new measurement. 2 To change Fly-Around altitude with the mouse To change the door height by set increments On the Standard toolbar, click the up or down arrow next to the Door Height Tool. Each click will increase (or decrease) the dimension by the set increment. Press and hold the right mouse button down to change the viewpoint. To specify an absolute Fly-Around altitude 1 On the View menu, click 3D Viewing Method>FlyAround Altitude. Type a new elevation measurement, then click OK. Note: The current measurement is always displayed next to the incremental arrows. Moving around in Cabinet Wizard Cabinet Wizard provides two of the same interactive 3D viewing options available in LiveView, the 3D WalkThrough and Fly-Around views. Using these tools, you can vary the viewing level by adjusting the angle to provide the best viewing capabilities available. 2 Applying Material or Color to Cabinets To view your design using Walk-Through 1 On the View menu, click 3D Viewing Method> Walk-Through, or click the Walk-Through button on the Cabinet Wizard window. Position the mouse pointer in the Cabinet Wizard window, then click and drag up to move inward or down to move outward. You can customize your cabinets' appearance by applying different materials or colors. Interiors, customizing your cabinetry is a simple drag and drop procedure. For more information, see "Material Workshop", which begins on page 143. To apply material to a cabinet To change Walk-Through elevation with the mouse 2 1 2 Press and hold the right mouse button down to raise and lower the viewpoint. In the Cabinet Wizard window, click the Material Tool. At the top of the Preview Bar, click the down arrow next to "Materials", to display the Materials style menu, then click to check the material you want. Options of the selected material will be displayed on the Preview Bar. Click the material you want to apply; hold down the mouse button and drag the material onto the cabinet in the Cabinet Wizard window. [. . . ] Click the Matching Apply button. To use Grouped Apply 1 2 3 Click the Rendering Style button or on the View menu, click 3D Rendering Style, Shaded View. Click the Grouped Apply button. 4 Click the color or material you want to apply; hold down the mouse button and drag the color or material onto the object. The color or material you selected is applied to the entire object. 4 Click the color or material you want to apply; hold down the mouse button and drag the color or material onto the object. The color or material you selected is applied to all places matching the material you are replacing. 342 PUNCH! [. . . ]