User manual PROFILO BM6224

[. . . ] reliable appliances Operating instructions 9000 533 738 (9004) Reset 3 sec. 10 9 Start 1 2 3 4 56 7 8 20 21 22 23 24 25 26 27 28 29 30 31 32 en Table of contents Washing the dishes . 15 15 15 15 15 16 16 16 16 16 16 17 17 17 17 18 18 19 19 19 20 20 21 22 22 22 23 23 23 23 23 24 24 24 24 25 25 25 Safety instructions . 15 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. ­ Please dispose of the packaging material in an environmentally friendly manner. [. . . ] chopping boards and baby bottles. Switching on the appliance ­ Turn on the tap fully. The programme starts running. Ï Intensive zone * Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display H. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). ¿ Extra drying * An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. 15 en Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. ­ Press button P until the displayed time corresponds with your requirements. ­ To delete the preselected starting time, press the button P until is indicated on the digital display. You can change your programme selection at any time until the programme starts. Interrupting the programme ­ Switch off ON/OFF switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. ­ To continue the programme, switch on the ON/OFF switch ( again. Terminating the programme (Reset) ­ Press START button @ for approx. ­ Switch off ON/OFF switch (. End of programme The programme has ended when the value : is indicated on the numerical display H. Switching off the appliance Short time after the end of the programme: ­ Switch off ON/OFF switch (. ­ Remove the utensils when they have cooled down. Changing the programme When the START button @ has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). ã=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. 16 en Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Rotate programme selector 8 until : is indicated on the digital display H. The factory-set value : is lit on the digital display H (intensive drying off). Change the setting as follows: ­ By rotating the programme selector 8, you can switch intensive drying on : or off : . The set value is saved. Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine ­ Check spray arm for grease and limescale deposits. If you find such deposits: ­ Fill detergent dispenser with detergent. [. . . ] Ensure that the fresh-water connection is not kinked, crushed or twisted. ­ When replacing the appliance, always use a new water supply hose. Inlet rate: minimum 10 litres/minute 23 en Water temperature: cold water preferred; hot water max. temperature 60 °C. Transportation Empty the dishwasher and secure loose parts. [. . . ]