User manual PLANET BIKE PROTEGE 5.0

[. . . ] In addition, Planet Bike will donate 25% of our profits from this purchases and any other Planet Bike product you buy, to non-profit bicycle advocacy groups to further benefit your cycling experience. Enjoy your new Protegé Bicycle Computer and thank you for making a difference! 3. Mounting Instructions STEP 1: Attach the wheel sensor to the right or left fork using two quick ties (diagram #1). MOUNTING SENSOR MOUNTING MAGNET (Front Wheel) Note: Do not fully tighten quick ties until final placement is determined. [. . . ] Clock will still be displayed. L + MacroMonitorTM LCD display displays up to 4 functions at once, allowing for fewer mode changes. L + "Buttonless" design for ease of use - push computer forward in bracket to change modes. L + Weather proof construction and heavy duty wire harness for all-weather use. PUSH AND RELEASE FORL CAUTION:L CHANGEL MODEL HOLD FORL LESS THAN ONE SECONDL OR YOU WILL RESET ALLL OF THE RIDE DATA 4. Computer Setup and Programming The Protegé comes with the battery preinstalled. Setup and Programing are facilitated by using the "set" and "mode" buttons loc ated on the SET underside of the computer case (diagram #6). To initiate programming, press "mode" button to display SCREEN 1, with "ODO" displayed on line 4. Depress and hold the "set" button for 3-4 seconds (use a pen or other such pointy object). Upon release, the M/H or K/H icon will flash. L L 1) Miles or Kilometers Selection: Once "M/H" or "K/H" is flashing, press "mode" to switch to desired selection. Press "set" to lock in your selection and advance the screen to Wheel Size Setting. L L 2) Wheel Size Setting (WSS): The screen will now display "2154" with the "4" flashing. This is the default "WSS". L * Background information: The bicycle computer calculates information based upon the distance traveled each time your wheel goes around. The wheel L size setting equals the distance in mm traveled in one revolution of your wheel. There are two methods to determine the wheel size setting. L Method 1: Read the tire size on the side wall of your tire and input the number that corresponds to your tire size on the wheel size chart to the right. Since there are many tire manufacturers and designs, tires listed as the same size from different manufacturers can actually vary significantly in their actual circumference. Therefore, we recommend for maximum accuracy in you computer readings, to use Method 2. L Method 2: Wheel Roll Out: For best results, find a flat smooth surface to perform the wheel roll out and inflate your tires to riding pressure. L 1) Place a piece of masking tape or draw a line on the surface to determine a starting position. L 2) Position the front tire valve at the 6:00 position (diagram #7) directly above the staring position. L 3) Roll the bicycle forward one revolution of the wheel on a straight line until the valve stem is again at the 6:00 position. (Note: Putting pressure on the handle bars to simulate body weight on the tire will give more accurate results. ) Mark the finishing position with masking tape or a line. Measure the distance between the starting and finishing positions in mm, this is your WSS. (Note: If you use an inch measuring tape, multiply inches by 25. 4 to achieve mm. ) This is your WSS in mm. L NOT USED INL THIS MODEL MODE 6 TIRE SIZE 20 x 1. 75 24 x 1. 0 24 x 1. 75 24 x 2. 0 26 x 1. 25 26 x 1. 5 26 x 1. 95 26 x 2. 0 26 x 2. 1 26 x 1 (559 mm) 26 x 1 (650 c) BATTERYL REMOVAL Imputing Wheel Size Setting (WSS)L A) Press "mode" button to change "flashing" first digit to desired selection. L B) Press "set" button to lock in your selection and advance to the next flashing digit. L C) Repeat steps A-B until all four digits are set. After the forth digit is set, it will L advance the screen to Odometer setting. WSSL 1502L 1750L 1894L 1925L 1950L 1996L 2055L 2066L 2070L 1925L 1925 TIRE SIZE 700 x 18C 700 x 20C 700 x 23C 700 x 28C 700 x 32C 700 x 38C WSSL 2072L 2091L 2105L 2143L 2160L 2184 For future reference, write your WSS here: 3) Odometer Setting: The digit on the far right will be flashing. (If you don't need to set the FINISHINGL POSITION Odometer, repeatedly press "set" to advance to clock setting. ) Repeat steps A-B again to set the Odometer. L L 4) Clock Setting: The hour digit on the far left will be flashing. To reset the clock only, press mode button until clock function is displayed on line four. [. . . ] Make sure the rubber water seal gasket is in 3) LCD screen is darkL place and the battery cover is flush with battery case. This is normally caused by overheating when computer is left sitting in the sun. Allow Refer to Computer Setup and Programming to re-input the computer to cool and it will return to normal. L setup data. [. . . ]