User manual PITSOS DIS4315

[. . . ] en Operating instructions 9000 510 606 (8906) Dishwasher Reset 3 sec. 11 10 9 8 End Start 1 2 3 4 9h 6h 3h 6 7 5 20 21 22 23 24 25 26 27 28 29 30 31 32 en Table of contents Washing the dishes . 15 15 15 15 15 16 16 16 16 16 16 17 17 17 17 18 18 19 19 19 20 20 21 22 22 22 22 23 23 23 23 23 24 24 24 24 24 Safety instructions . 15 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. ­ Please dispose of the packaging material in an environmentally friendly manner. [. . . ] To obtain optimum cleaning and drying results at a reduced running time, water and energy consumption are increased. Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. If the Aqua sensor is active, "clean" rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3­6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Ï Intensive zone * Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. · Hygiene * The temperature is increased during the cleaning process. chopping boards and baby bottles. Switching on the appliance ­ Turn on the tap fully. he programme starts running. § Half load * If you have only a few items to wash (e. g. It is recommended to put a little less detergent in the detergent dispenser than for a full load. Timer programming * * depending on model You can delay the start of the programme by 3, 6 or 9 hours. ­ Keep pressing the Preselected starting time button H until the appropriate display 3h, 6h or 9h is lit. selection at any time until the programme starts. ¿ Extra drying * An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. ­ To delete the preselected starting time, keep pressing the Preselected starting time button H until none of the displays 3h, 6h or 9h is lit. You can change your programme 15 en End of programme The programme has ended when the End display )" is lit. Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Rotate programme selector 8 until the "Check water supply" display h flashes. To change the setting, ­ By rotating the programme selector 8, you can switch on intensive drying (End display)" is lit) or switch off intensive drying (End display )" is not lit). The setting is saved. Switching off the appliance Short time after the end of the programme: ­ Switch off ON/OFF switch (. ­ Remove the utensils when they have cooled down. ã=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme ­ Switch off ON/OFF switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. ­ To continue the programme, switch on the ON/OFF switch ( again. Terminating the programme (Reset) ­ Press START button @ for approx. Switch off ON/OFF switch (. Changing the programme When the START button @ has been pressed, the programme cannot be changed. [. . . ] ­ The socket must be near the appliance and freely accessible following installation. ­ A power cord extension may be purchased from customer service only. ­ Use only a residual current operated circuit-breaker which features the symbol , . Only this extension guarantees compliance with the currently valid regulations. [. . . ]