User manual PITSOS DGS6728

[. . . ] HQ 2SHUDWLQJ LQVWUXFWLRQV 'LVKZDVKHU $%& 5HVHW VHF 6WDUW 5HVHW VHF en Table of contents Washing the dishes . 15 15 15 15 16 16 16 16 16 17 17 17 17 18 18 18 18 19 19 20 20 20 20 21 21 22 23 23 23 24 24 24 24 25 25 25 26 26 26 26 26 Safety instructions . 15 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. ­ Please dispose of the packaging material in an environmentally friendly manner. [. . . ] There is a slight increase in the energy consumption. 15 en Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display )". The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Switching off automatically after the end of the programme * * depending on model To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). Appliance does not switch off automatically : Off after 1 min : Off after 120 min ­ Close the door. ­ Hold down programme button # and press START button P until : . . . The LED for button # flashes and the digital display )" displays the factory setting : . ­ Press programme button # until the factory set value : is indicated on the digital display )". Each time the button is pressed, the set value increases by one level; when the value of : has been reached, the display jumps back to : (off). : Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. ­ Press @ + or ­ button until the displayed time corresponds with your requirements. ­ To delete timer programming, press the @ + or ­ button until )" : is indicated on the digital display. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when the value : is indicated on the numerical display )". Switching off the appliance Short time after the end of the programme: ­ Switch off ON/OFF switch (. ­ Remove the utensils when they have cooled down. 16 en ã=Warning Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Hold down programme button # and press START button P until the digital display )" : . . . The LED for button # flashes and the digital display )" displays the factory setting : . ­ Press programme button # until the factory set value : is indicated on the digital display )". To change the setting, ­ Press the button 3 to switch the Intensive drying on : or off : . The set value is saved. At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme ­ Switch off ON/OFF switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. ­ To continue the programme, switch on the ON/OFF switch ( again. Terminating the programme (Reset) ­ Press START button P for approx. ­ Switch off ON/OFF switch (. Changing the programme When the START button P has been pressed, the programme cannot be changed. [. . . ] Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a suitable installation, e. g. The hot water setting : allows you to adjust your appliance optimally to operation with hot water. It is recommended to have a water temperature (temperature of the incoming water) of at least 40 °C and no more than 60 °C. It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler. [. . . ]