User manual PIAGGIO XEVO

[. . . ] Com manuals search engine MANUALE STAZIONE DI SERVIZIO XEVO 400ie The descriptions and illustrations given in this publication are not binding. While the basic specifications as described and illustrated in this manual remain unchanged, PIAGGIO-GILERA reserves the right, at any time and without being required to update this publication beforehand, to make any changes to components, parts or accessories, which it considers necessary to improve the product or which are required for manufacturing or construction reasons. Not all versions shown in this publication are available in all countries. The availability of single versions should be checked at the official Piaggio sales network. [. . . ] The injection control unit power supply is necessary for the Stepper motor management. In case of power supply faults, the diagnostic tester gives the information "NO REPLY FROM THE CONTROL UNIT". To carry out the check, proceed as follows: Specific tooling 020680Y Diagnosis Tool 1 - Check whether the immobiliser system LED indicates that the switch is in position "ON" and that the deterrent flashing is on. YES go to 3 3 - Switch set to "ON" with side stand raised and emergency switch set to "OFF". YES go to 5 NO go to 4 4 - Check the instrument unit and its power supply. YES go to 6 NO go to 7 6 - The injection control unit is certainly powered. Com manuals search engine XEVO 400ie Injection 8 - Fix any wiring short circuits and replace the fuse. YES go to 1 NO go to 9 9 - Check any short circuit on decoder or control unit and replace, if necessary. YES go to 1 10 - Place the special tool between control unit and power supply system. Disconnect the main decoder connector and check the following conditions: Terminal no. 4= battery negative YES go to 11 NO go to 13 Specific tooling 020481Y Control unit interface wiring 11 - Decoder with proper base power supply. Use the special tool to check the control unit power supply: Pin 17 = battery positive Pin 23 = battery negative YES go to 12 NO go to 13 12 - Control unit with proper base power supply. 13 - If the battery negative is not present, check continuity between Pin 23 of the special tool and earth. Detect the presence of the battery positive on Pin 17 of the special tool and on pin 3 of the decoder connector. Key-switch power supply circuit check A failure of the constant power supply disables both ignition and injection functions. In case of power supply faults, the diagnostic tester gives the information "NO REPLY FROM THE CONTROL UNIT". Com manuals search engine Injection XEVO 400ie Specific tooling 020680Y Diagnosis Tool 1 - Check whether the immobilizer system LED indicates switching to "ON" YES go to 2 NO go to 4 2 - Raise the side stand. Check whether the injection telltale light turns on for 5 seconds YES go to 3 NO go to 4 3 - Continuous power supplies are regular 4 - Check that fuse No. YES go to 5 NO go to 6 5 - Place the special tool between control unit and injection system. YES go to 7 Specific tooling 020481Y Control unit interface wiring 6 - Fix any short circuits and replace the fuse. Check decoder and control unit, if necessary YES go to 1 7 - Disconnect the main decoder connector and check the following conditions: switch set to "ON", switch to "RUN" and side stand raised Terminal no. 4= battery negative YES go to 8 NO go to 10 8 - Decoder with proper continuous power supply. [. . . ] Com manuals search engine XEVO 400ie Time Swing-arm SWINGING ARM 1 2 3 Code 003081 004058 001072 Action Swinging arm support flange - Replacement Silent block - Replacement Engine/frame swinging arm attachment - Replacement Duration TIME - 353 Downloaded from www. Com manuals search engine Time XEVO 400ie Seat SADDLE 1 2 Code 004003 004068 Action Saddle - Replacement Passenger handgrip - Replacement Duration TIME - 354 Downloaded from www. Com manuals search engine XEVO 400ie Time Locks LOCKS + LOCK TRANSMISSIONS 1 2 3 4 5 6 7 8 Code 004010 005146 005133 004054 004173 004158 004172 005072 Action Anti-theft lock - Replacement Electric saddle opening activator Replacement Electric glove box activator - Replacement Saddle lock catch - Replacement Trunk opening splitter - Replacement Saddle opening splitter - Replacement Rear case lock catch - Replacement Immobilizer aerial - Replacement Duration Turn signal lights Rear lights TIME - 355 Downloaded from www. Com manuals search engine Time XEVO 400ie REAR LIGHTS 1 2 3 4 5 6 7 8 Code 005005 005048 005031 005032 005022 005066 005068 005030 Action Taillight - change number plate holder - Replacement number plate light bulb - Replacement number plate light glass - Replacement Rear turning indicators - Replacement Rear light bulbs - Replacement Rear turning indicator bulb - Replacement Rear headlight cable unit- Replacement Duration Front lights TIME - 356 Downloaded from www. [. . . ]