User manual PHILIPS MX5100VR

[. . . ] E9017FD_EN. qx3 03. 8. 6 10:13 AM Page 1 AAA AAA Digital Video Disc Player Video Cassette Recorder FM/MW Radio Tuner MX5100VR R 1 1 E9017FD_EN. qx3 03. 8. 6 10:13 AM Page 2 General Information The region code for this set is 2. Since it is usual for DVD movies to be released at different times in different regions of the world, all players have region codes and discs can have an optional region code. If you load a disc of a different region code to your player, you will see the region code notice on the screen. The disc will not playback, and should be unloaded. Thank you for purchasing this Philips System. This Owner's Manual explains the basic operation of this System. [. . . ] Press PLAY B. While disc is playing, press PAUSE k at the point you wish to start recording. Press STOP C. Programming a Recording (TIMER) Use a TIMER programming to automatically start and stop a recording at a later time or date. The System will switch to the right programme number and begin recording at the correct time. With this System, you can pre-programme up to eight recordings within a period of one year. To make a programmed recording, your System needs to know: * the date you want to make the recording * the programme number of the TV channel * the start and stop time of the recording * VPS or PDC on or off This information is saved in a TIMER block. 'VPS' (Video Programming System)/ 'PDC' (Programme Delivery Control) are used to control the start and duration of TV channel recordings. If a TV programme starts earlier or ends later than scheduled, the System will turn on and off at the correct time. But if your TV guide shows a VPS or PDC time which is different from the programme's scheduled start time, e. g. 20. 10 (VPS/PDC 20. 14), you must enter the VPS/PDC time exact to the minute. If you want a start time different from the VPS/PDC time, you must switch VPS/PDC off. English General information 1 2 3 4 5 6 7 Recording(From DVD To VCR) 1 Insert a DVD without copyright protection in the tray. 2 Insert a video cassette tape with its erase prevention tab in place. 4 Enter "004" with numerical key pads to appear "DISC" on the TV screen. 8 Press VCR, then STOP C to stop recording. Programming a recording (with the 'SHOWVIEW® system') R 1 2 3 4 You no longer need to tediously enter the date, programme number, start and end time. All the information needed for programming is contained in the SHOWVIEW-programming number. You can find this SHOWVIEW number in most TV listing magazines written next to the concerned programme. ber. This number is up to 9 digits 12345 ­ ­ ­ ­ long and can be found next to the start time of the TV programme in your TV listing magazine. [e. g: 1SET=SV/V+ CORRECT=CLEAR 234-5 or 1 234 5] END=EXIT If you make a mistake, you can clear your input with CLEAR. ONCE Select ONCE, DAILY or WEEKLY DAILY WEEKLY recording with K/L. Then press B. SELECT K L CHOOSE B END=EXIT Selecting once/daily/weekly recordings Using K/L, select from the following options: 'ONCE': Recording once 'DAILY': Repeated daily recordings (Monday to Friday) 'WEEKLY': Repeated weekly recordings (every week on the same day) '- -' appears at PROG. * The programme number of the TV channel has not yet been assigned to the SHOWVIEW number. Using the numerical key pads, select the corresponding programme number (name) of the TV channel. The following message appears on the screen:'ERROR' * The entered SHOWVIEW number is incorrect. * Check the time/date (see chapter 'Installing your video', section 'Setting the time and date'). Daily programming can only be used for recordings to be made from Monday to Friday. The following message appears on the screen:'TIMER NOT COMPLETED' * The channel is wrong. 13 E9017FD_EN. qx3 03. 8. 6 10:13 AM Page 14 Programming a Recording (TIMER) 5 The decoded data appears after confirmation. You can go back to change the data. [. . . ] Cleaning the disc lens · After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with the cleaner. 22 E9017FD_EN. qx3 03. 8. 6 10:13 AM Page 23 Specifications VCR Video Heads Four heads - Hi-Fi Antenna VHF/UHF - 75 ohm external antenna terminal DVD Color System PAL Amplifier Output power (rms, 4 ohms, 1 kHz, 10% Total Harmonic Distortion) 360W total - Front 75W/channel - Center 75W - Rear (Surround) 75W/channel - Subwoofer 75W FTC(Federal Trade Commission) (4 ohms, 120 Hz to 12. 5 kHz, 10 % Total Harmonic Distortion) 2 X 60W Frequency Response DVD (linear sound): 20 Hz to 22 kHz (sample rate: 48 kHz) 20 Hz to 44 kHz (surround off) (sample rate: 96 kHz) Audio CD: 20 Hz to 20 kHz Signal-to-Noise Ratio Audio CD: 120 dB (JEITA: Japan Electronics and Information Technology Industries Association) Dynamic Range DVD (linear sound): 99 dB Audio CD: 99 dB (JEITA) Total Distortion Factor Audio CD: 0. 003% (JEITA) DVD: 0. 003% Wow and Flutter Below the measurement limitation (±0. 001% W PEAK) (JEITA) Power Requirement 220­240V AC, 50 Hz Power Consumption Power on: 50 W Power off (standby): 5 W ( When CLOCK DISPLAY set to OFF. ) Operating Temperature 5°C to 40°C Relative Humidity 30% to 80% Dimensions (w x h x d) Receiver (System): 43. 5 x 9. 9 x 39. 2 cm Front Speakers: 9. 4 x 15. 5 x 8. 9 cm Rear Speakers: 9. 4 x 15. 5 x 8. 9 cm Center Speaker: 43. 5 x 7. 2 x 6. 4 cm Subwoofer: 19. 6 x 39. 1 x 43. 2 cm Weight 7. 8 kg NOTE: Designs and specifications are subject to change without notice. Troubleshooting Problem No power No picture Distorted picture Completely distorted picture or black/white picture with DVD No sound or distorted sound No audio at digital output No DTS audio at analog output No sound and picture Picture freezes momentarily during playback Solution ­ Check if the AC power cord is properly connected. ­ Sometimes a small amount of picture distortion may appear. This is not a malfunction. ­ Check if the audio format of the selected audio language matches your receiver capabilities. [. . . ]