User manual PHILIPS MCM233

[. . . ] · Ensure that you always have easy access to the power cord, plug or adaptor to disconnect this apparatus from the power. l Unplug this apparatus during lightning storms or when unused for long periods of time. 4 EN Hearing safety Listen at a moderate volume. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. The higher decibel ranges are offered for those that may have already experienced some hearing loss. Over time your hearing `comfort level' adapts to higher volumes of sound. [. . . ] o · 10 EN Stop play or erase a program. 3 Get started Caution · Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. 3 Close the battery compartment. 1 3 2 Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of this apparatus. ___________________________ Note · If you are not going to use the remote control for a long time, remove the batteries. · Do not use old and new or different types of batteries in combination. · Batteries contain chemical substances, so they should be disposed of properly. Placement You can place the unit on a flat surface or mount the unit on a wall. Connect power Caution · Risk of product damage!Ensure that the power supply · voltage corresponds to the voltage printed on the back or the underside of the unit. When you unplug the AC power cord, always pull the plug from the socket. Before you connect the AC power cord, ensure that you have completed all other connections. Mount on a wall To wall mount the unit, see the included separate sheet of wall mounting instructions. Prepare the remote control Caution · Risk of explosion!Never discard batteries in fire. · To insert the remote control battery: 1 2 Open the battery compartment. Insert 2 AAA batteries (not supplied) with correct polarity (+/-) as indicated. EN 11 English 1 Connect the power adaptor to: · the DC IN jack on the main unit. · the wall outlet. 6 7 Press / to set the minute. Press PROG/CLOCK SET to confirm the clock setting. Auto install radio stations When you connect power and no radio stations are stored, the unit automatically begins to store radio stations. Turn on 1 Press . » The unit switches to the last selected source. 1 Connect the unit to the power supply. » [AUTO INSTALL PRESS -- PLAY KEY](auto install press -- play key) is displayed. » The unit automatically stores radio stations with sufficient signal strength. » When all the available radio stations are stored, the first preset radio station is broadcast automatically. Switch to standby 2 1 Press again to switch the unit to standby mode. » The clock (if set) appears on the display panel. To switch the unit to Eco Power Standby mode: 1 In the standby mode, press and hold for more than 2 seconds. » The backlight on the display panel turns off. Tip Set clock Note · You can set the clock in the standby mode only. · The unit switches to Eco Power Standby mode after 15 minutes in standby mode. 1 Press and hold PROG/CLOCK SET to enter the clock setting mode. » The first programmed radio station is broadcast automatically. · For optimal reception, fully extend and adjust the position of the antenna. FM stations with RDS Radio Data System (RDS) is a service that sends additional broadcast information along with FM stations. If you listen to a FM station with RDS signal, "RDS" is displayed. Program radio stations manually You can program a maximum of 20 preset radio stations (FM). Display RDS information 1 For an FM station with RDS, press RDS/DISPLAY repeatedly to display various broadcast information. 1 2 14 Tune to a radio station. Press PROG/CLOCK SET to activate program mode. EN 6 Play options Pause/resume play 1 During play, press play. to pause/resume 2 Program tracks Note Skip to a track For CD: · You can program tracks only when the play stops. You can program a maximum of 40 tracks. 1 2 3 Press / to select another track. · To select a track directly, you can also press a key on the numerical keypad. [. . . ] · Wait until the moisture condensation at the lens has cleared. Remote control does not work · Before pressing any function button, first select the correct source with the remote control instead of the main unit. · Insert the battery with its polarities (+/­ signs) aligned as indicated. 20 EN Replace the battery. Aim the remote control directly at the sensor on the front of the unit. [. . . ]