User manual PHILIPS LC4331

[. . . ] Philips Multimedia projector cBright 1 Series User guide English Menu OK AV te Mu e Volum Stand by p Lam RC ne Keysto 0. Controls and connections 1 2 3 4 AV te Mu Menu OK 5 6 7 8 9 AV Mute Source Keystone Lamp Stand by On RC @ $ fig. 1 1 2 3 4 Stand by On 1 2 Right Left Mouse MOUSE Volume VOLUME 3 OK Menu MENU !0 4 Volume 5 6 7 SVGA/XGA version Mute MUTE AV Mute AV MUTE Source SOURCE D-Freeze D-FREEZE D-Zoom D-ZOOM 9 8 5 6 7 XGA Impact Available as accessory for SVGA/XGA version g Stand by On AV MUTE Source fig. [. . . ] Put the lens cap back in place to prevent dust, dirt or other contamination from harming or damaging the front of the projector lens when moving the projector. AV Mute Note: Never place the projector on the side where the connections are located. 9 Menu OK Stand by e Volum p Lam RC tone Keys 7. CABLE/ADAPTER Video/computer cables and adapter CONNECTIONS Projector side Computer/AV products side Mini D-Sub 15P (male) USB connector 4P (female) RCA pin (male) x 3 1 Integrated VGA/USB Cable Mini D-Sub 15P (male) USB connector 4P (female) 2 RCA Audio Video Cable RCA pin (male) x 3 3 Scart/RCA-AV Adapter (depending on region) Video/computer cables and adapter These accessories (1 to 3) are supplied with the product for connecting the projector to computer/AV equipment. The numbers in the left-hand column correspond with the numbers in the connection diagrams on the following pages. When connecting the projector to a Macintosh computer, a programmable VGA/MAC adapter is available as an optional Philips cable accessory. 10 7. Installation Connecting to a computer Connecting to a computer ­ ­ ­ ­ Caution!The data input is suitable for both Apple Macintosh computers (Power Book and Power Mac) as well as for IBM compatible PCs. The data output of IBM compatible PCs can be connected directly to the projector using standard data cables. Apple Macintosh computers may need a conversion plug (optional) added to the standard data cable. The figures in brackets (1) correspond to the figures in the accessories diagram. 4 of `Controls and connections'. PC (Desk Top/Lap Top)/ MACINTOSH (Desk Top/Power Book/Power Mac) (b) Audio out USB R Audio in R L L Video S-Video Data out Data in (g) Data in Data out USB connection A USB interface is available via an upstream connector. When the projector's USB (upstream) connector is connected to a PC or an Apple Macintosh computer equipped with a USB downlink connection, it will identify as a USB device. It is possible to: ­ control the cursor of the computer via the projector remote control, ­ play audio information from the computer via the projector speaker, and ­ the display settings of the computer will be changed to fit the capability of the projector. Projector 1 1 Mac/PC optional Philips VGA/MAC adapter USB Data out Data out A 1. Connect the Data out terminal of the computer to the Data in terminal (g) of the projector and secure the plugs by tightening the thumb screws. When connecting the projector to a Macintosh computer use the VGA/MAC adaptor (optional). Connect the USB (upstream) socket (b) of the projector to the USB downstream port of the computer. ­ You can now manipulate the mouse cursor on the computer and on the screen, using Cursor Control. Audio information from the computer will be played via the projector speaker. Note: If the mouse cursor does not react when moving the cursor control on the remote control: 3. Check that the Remote Control indicator on the projector flashes green when you move the trackball. ­ If it does not: Check that you have switched on the remote control. If you have, check that the batteries are installed properly and/or replace the batteries. [. . . ] Troubleshooting Image is blurred If a fault occurs, first check the points listed below before taking the projector for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service organisation. Warning: Under no circumstances should you try to repair the projector yourself as this could invalidate the warranty. PROBLEM ­ · ­ · ­ · Image is not focused. Connect signal cable correctly. Image does not match up with the projected screen ­ · POSSIBLE CAUSE SOLUTION ­ · · Image is not displayed Shift and/or Horizontal size are not adjusted correctly. [. . . ]