User manual PHILIPS FW-C80

[. . . ] FW- C80 with 3 CD changer Mini Hi-Fi System pg 01-26/C80/22-Eng 1 3/6/00, 2:22 PM 3139 116 19681 Important notes for users in the U. K. To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. [. . . ] REV DUB (HSD) RECORD BASS TREBLE PLUS wOOx TECHNOLOGY LEVEL TM The system will start searching for all radio stations with RDS and then followed by radio stations on FM, MW and LW band respectively. TM The system will stop searching when all the available radio stations are stored or when the memory for 40 preset radio stations is used. TM The system will remain tuned to the last stored preset radio station. 4 Press à or á to tune to the desired frequency. · If you wish to store the radio station to another preset number, press 4 or 3 to select the desired preset number. · Repeat steps 3 ­ 5 to store other preset radio stations. L SO UN DC English 16 Note: ­ For 'EASY SET' feature, please refer to page 11. Tuning to radio stations 1 Press TUNER (BAND) to select TUNER mode. 2 Press TUNER (BAND) again to select the desired waveband : FM, MW or LW. TM The display will show "SEARCH" until a radio station with sufficient signal strength is found. · Repeat this procedure until the desired station is reached. · To tune to a weak station, briefly press à or á repeatedly until the display shows the desired frequency and/or when the best reception has been obtained. Storing Preset Stations You can store up to 40 radio stations in the memory. When a preset radio station is selected, the preset number appears next to the frequency on the display. TM The PROGRAM starts flashing and "AUTO" will be displayed. Notes: ­ You can cancel the automatic programming by pressing PROG orÇ (on the system only). ­ If you want to reserve a section of preset numbers, for example preset numbers 1 to 9, select preset 10 before starting automatic programming, only the preset numbers 10 to 40 will be programmed. Manual programming 1 Press TUNER (BAND). 2 Press TUNER (BAND) again to select the desired waveband : FM, MW or LW. TM The next available preset number will be displayed for selection. Notes: ­ When 40 radio stations are stored and you attempt to store another radio station, the display will show "PROGRAM FULL". If you want to change an existing preset number, repeat steps 3 ­ 5. ­ You can cancel manual programming by pressing Ç (on the system only). ­ During programming, if no button is pressed within 20 seconds, the system will exit program mode automatically. Tuning to Preset Radio Stations · Press 4 or 3 to select the desired preset number. TM The preset number, radio frequency, and waveband appear on the display. pg 01-26/C80/22-Eng 16 3/6/00, 2:23 PM 3139 116 19681 TUNER Receiving RDS Radio Station Ç RDS (Radio Data System) is a broadcasting service that allows FM stations to send additional information along with the regular FM radio signal. This additional information can contain: · STATION NAME: The radio station name is displayed. · PROGRAM TYPE: The following program types exist and can be received by your tuner: News, Affairs, Info, Sport, Educate, Drama, Culture, Science, Varied, Pop M, Rock M, M. O. R. When you have tuned to a RDS station, the RDS logo (Ç) and the radio station name will appear on the display: · The display normally shows the radio station name if available. By repeatedly pressing RDS button you can change the type of display information: TM The display shows in turn: STATION NAME TM PROGRAM TYPE TM RADIO TEXT TM TUNED FREQUENCY TM STATION NAME . . . Note: ­ When you press the RDS button and the display shows "NO RDS", it indicates that either the tuned station is not transmitting RDS signal or it is a non RDS station. RDS Clock Some RDS station may be transmitting a real clock time at an interval of every minute. TM If the station does not transmit RDS clock, "NO RDS TIME" will be displayed. [. . . ] Cleaning Discs · When a disc becomes dirty, clean it with a cleaning cloth. · Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analog records. Cleaning the CD lens · After prolonged use, dirt or dust may accumulate at the CD lens. To ensure good playback quality, clean the CD lens with Philips CD Lens Cleaner or any commercially available cleaner. [. . . ]