User manual PHILIPS FB201-00S

[. . . ] Make sure that curtains or other objects never cover the ventilation slots on the product. Risk of injury or damage to the product! Risk of overheating! • • Note •• The type plate is located on the back of the product. Important notes for users in the U. K. Mains fuse This information applies only to products with a UK mains plug. If you replace the fuse, use one with: • the ratings shown on the plug, • • Contact your dealer if you are not sure about what type of fuse to use. Caution: To conform with the EMC directive (2004/108/EC), do not detach the plug from the power cord. How to connect a plug a BS 1362 approval, and the ASTA approval mark. The wires in the power cord are colored as follows: blue = neutral (N), brown = live (L). If the colors do not correspond with the colors on your plug, identify the terminals in your plug as follows: 1 2 3 Connect the blue wire to the terminal marked N or colored black. [. . . ] Before you replace the plug cover, make sure that the cord grip is clamped over the sheath of the cable and not just over the two wires in the cable. 2 3 4 Press the What’s in the box (Fig. 2-2) »» The product switches to the last selected source. knob or turn the SOURCE knob. • To switch the product to standby mode, press the knob again. 5 1 2 3 4 5 »» Set the clock (Fig. 3) In standby mode, press and hold the (12-hour time format) or (24-hour time format) blinks. knob for 2 seconds. Turn the knob to select a time format, and then press the »» Hour digits blink. knob to confirm. »» Minute digits blink. Turn the knob to set the hour, and then press the knob to confirm. knob to confirm. 6 1 2 Listen to FM radio stations Turn the SOURCE knob to switch the product to FM mode. Search for radio stations automatically or manually. Note •• For optimal reception, fully extend the antenna and adjust its •• You can store a maximum of 30 FM radio stations. position. Search for a radio station automatically Press SCAN to activate the auto search. »» After a strong station is detected, the search stops and the radio station is broadcast. Search for a radio station manually Turn the displayed. knob until the frequency of target radio station is Store radio stations automatically (Fig. 4) Press and hold SCAN to activate the auto search. »» After the search is complete, the first stored radio station is broadcast. To tune to a stored radio station, turn the PRESET knob until its frequency is displayed. • Program radio stations manually 1 2 3 4 5 • Tune to a radio station. knob to confirm. »» The radio station is stored with the selected sequence number. Repeat steps 1-4 to program more radio stations. To tune to a preset radio station, turn the PRESET knob until its frequency is displayed. Note •• If you store a radio station with the sequence number of another one, the earlier one is overwritten. Display RDS information Radio Data System (RDS) is a service that allows FM stations to transmit additional information. When you tune to an FM radio station that transmits RDS signals, the station name is displayed. 1 2 Tune to an RDS station. • If no DAB station is stored, the product starts automatic search. knob to start listening. Re-scan for stations Full scan is used to perform a wide range search for DAB radio stations. Press the »» After the scanning is complete, the first detected station is broadcast. knob to start scanning for available DAB stations. Tune to a station manually With this feature, you can tune to a specific channel/frequency manually. In addition to antenna orientation for better radio reception, the optimal reception can also be obtained with this feature. 1 2 Press the Turn the knob to access the station list. knob to select a station from 5A to 13F. 3 Press the knob to confirm the option. DRC (Dynamic Range Control) DRC adds or removes a degree of compensation for the differences in the dynamic range between radio stations. 1 Press the knob to access the sub-menus. 2 3 Turn the knob to select an option. (The asterisk indicates the current setting. ) • <DRC low>: Medium compensation applied. Press the knob to confirm the option. Remove invalid stations This option lists active stations and removes any stations that are in the list but have no service in your area. In front of the station name of an invalid station, a question mark (?) is displayed. 1 2 3 Press the knob to access the sub-menus. Turn the knob to select an option. Press the knob to confirm the option. System menus 1 Press the knob to access system menus. 2 • Turn the For details, refer to the section ‘Use system menus‘. knob to select a sub-menu. 8 • • • Use system menus check the version of current software of this product, upgrade the software, and reset the product to factory default status. Use the system menus to Check the current software version Press the knob to display the version of current software. Reset the product 1 2 3 Press the knob to display the options. Turn the knob to select an option. Press the knob to confirm the option. Upgrade the software 1 2 Go to www. philips. com/support. Search for support information about your product with “FB201-00S/10“ as the keyword. »» When an upgrade packet is available, the link of “Firmware Upgrade Readme File“ is accessible. [. . . ] The exact wording of this link name may vary in different languages. 3 4 5 Click the link of “Firmware Upgrade Readme File“. Follow the instructions to complete the upgrade. 9 Listen to an external device (Fig. Connect the MP3 link cable to • the MP3-LINK socket on the back panel of this product, and • the headphone jack on the external device. You can also listen to an external audio device, for example, MP3 player, through this product. 1 2 3 Play the external device (refer to its user manual). 10 Turn the Adjust the volume knob. 11 Troubleshooting Warning •• Never remove the casing of this product. To keep the warranty valid, never try to repair the product yourself. If you encounter problems when using this product, check the following points before requesting service. [. . . ]