User manual PHILIPS DVD757VR

[. . . ] AAA AAA Digital Video Disc Player & Video Cassette Recorder DVD757VR R 1 General Information The region code for this set is 2. Since it is usual for DVD movies to be released at different times in different regions of the world, all players have region codes and discs can have an optional region code. If you load a disc of a different region code to your player, you will see the region code notice on the screen. The disc will not playback, and should be unloaded. English Introduction wThank you for purchasing this Philips DVD/ VCR. This Owner's Manual explains the basic operation of this DVD/VCR. 2 Environmental Information All unnecessary packaging has been omitted. [. . . ] Select the required recording END=EXIT speed with B. Switching 'Direct Record' on or off 1 Switch on the TV. 3 Select 'RECORD SET UP' with SELECT K L CHOOSE B K/L and confirm with B. RECORD SPEED [SP] 4 In 'DIRECT RECORD', select 'OFF' ¡ DIRECT RECORD [OFF] RECORD LINK [OFF] (Direct Record off) or 'ON' (Direct Record on) with B. 6 Press STANDBY-ON. END=EXIT 'SP'/'LP' /'AUTO' 'SP': StandardPlay (normal recording speed) offers the usual firstclass picture quality. 'LP': LongPlay (half recording speed, double recording time). 6 hours can be recorded on a 3-hour cassette (E180) with a somewhat reduced picture quality. If there is not enough space on the tape to record a programmed recording in standard speed, the recording is automatically done in 'LP' (Longplay). 6 To end, press STATUS/EXIT. Direct dubbing Follow the steps below to copy a DVD or video disc to a videotape. This will be possible only if the DVD is not copy protected. Make sure the tape's record tab is intact and the tape is long enough to record the disc. Press PLAY B. While disc is playing, press PAUSE k at the point you wish to start recording. Press STOP C. 1 Automatic controlled recording from a satellite receiver (RECORD LINK) This function automatically starts recording on the switched-off DVD/VCR when a video signal is recognised through the connected scart cable. If your satellite receiver has a programming function, the recording will start automatically (as long as the satellite receiver is switched on). Use a scart cable to connect scart socket AV2(DECODER) on the DVD/VCR to the corresponding scart socket on the satellite receiver. Programme the satellite receiver with the required information (programme number of the TV channel, END=EXIT start time, end time). If necessary, please see the operating instructions for your satellite receiver. The DVD/VCR is now ready to record. The beginning and end of the recording is controlled via scart socket AV2(DECODER). 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 Recording(From DVD To VCR) 1 Insert a DVD without copyright protection in the tray. 2 Insert a video cassette tape with its erase prevention tab in place. 4 Enter "004" with numerical key pads to appear "DISC" on the TV screen. 8 Press VCR, then STOP C to stop recording. 10 11 English Programming a Recording (TIMER) General information Use a TIMER programming to automatically start and stop a recording at a later time or date. The DVD/VCR will switch to the right programme number and begin recording at the correct time. With this DVD/VCR, you can pre-programme up to eight recordings within a period of one year. To make a programmed recording, your DVD/VCR needs to know: * the date you want to make the recording * the programme number of the TV channel * the start and stop time of the recording * VPS or PDC on or off This information is saved in a TIMER block. 'VPS' (Video Programming System)/ 'PDC' (Programme Delivery Control) are used to control the start and duration of TV channel recordings. If a TV programme starts earlier or ends later than scheduled, the DVD/VCR will turn on and off at the correct time. But if your TV guide shows a VPS or PDC time which is different from the programme's scheduled start time, e. g. [. . . ] · Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analogue records. Cleaning the disc lens · After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with the cleaner. 18 Specifications PLAYBACK SYSTEM DVD Video, Audio CD, DVD+RW, DVD-R/RW, DVD+R, CD-R/RW, VIDEO CD TV STANDARD (PAL/50Hz) (NTSC/60Hz) Number of lines 625 525 Playback Multistandard (PAL/NTSC) VIDEO PERFORMANCE Video output 1 Vpp into 75 ohm RGB (SCART) output 0. 7 Vpp into 75 ohm Video Shift Left/Right VIDEO CASSETTE RECORDER Video heads Four heads Hi-Fi Antenna VHF/UHF - 75 ohm VHF output 75 ohm unbalanced AUDIO FORMAT Digital MPEG Compressed Digital Dolby Digital 16, 20, 24 bits PCM fs, 44. 1, 48, 96 kHz Analogue Stereo Sound Dolby Surround-compatible downmix from Dolby Digital multi-channel sound 3D Sound for virtual 5. 1 channel sound on 2 speakers AUDIO PERFORMANCE DA Converter 24 bits DVD CD Signal-Noise (1kHz) Dynamic Range (1kHz) Distortion and Noise (1kHz) CONNECTIONS SCART 2x Euroconnector S-Video OutputMini DIN, 4 pins Audio L+R output 2x Cinch (white/red) Digital Output 1 coaxial, 1 optical IEC958 for CDDA / LPCM IEC1937 for MPEG1/2, Dolby Digital CABINET Dimensions (w x h x d) 435 x 99 x 218 mm Weight Approximately 3. 8 Kg POWER SUPPLY (UNIVERSAL) Power inlet 220 ~ 240 V , 50 Hz Power usage Approx. 30 W Power usage standby 9. 2 W (standby : 5. 0 W) (When CLOCK DISPLAY set to OFF. ) Specifications subject to change without prior notice Troubleshooting Problem No power No picture Distorted picture Completely distorted picture or black/white picture with DVD No sound or distorted sound No audio at digital output Solution ­ Check if the AC power cord is properly connected. [. . . ]