User manual PHILIPS AZ1310-00C

[. . . ] Note : The DBB setting, tuner presets and the volume level (maximum to 20) will be retained in the set's memory. TM Display: shows when activated. CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. POWER SUPPLY Whenever convenient, use the AC power supply to conserve battery life. Make sure you remove the power plug from the set and wall outlet before inserting batteries. Batteries (not included) · Insert 6 batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity. [. . . ] (See 6) · Remote control (AZ1325 model only) Insert 2 batteries, type AAA, R03 or UM4 (preferably alkaline). Press and hold SEARCH or § until the frequency in the display starts running. TM The radio automatically tunes to a station of sufficient reception. · To tune to a weak station, press or § briefly and repeatedly until you have found optimal reception. To improve radio reception: · For FM, extend, incline and turn the telescopic aerial. Programming radio stations You can store up to a total of 30 radio stations (20 FM and 10 MW) in the memory, manually or automatically (Autostore). DIGITAL TUNER Manual programming 1. · Remote control (AZ1325 models only): Press PRESET + / once or more to select a preset station. Repeat steps 1-4 to store other stations. CD PLAYER Playing a CD This CD player plays Audio Discs including CDRecordables and CD-Rewritables. Note : CD play will also stop when: - the CD door is opened - the CD has reached the end - you select MW / FM function. Selecting a different track · Press SEARCH or § once or repeatedly to select your track. · Open the CD door. SAFETY & MAINTENANCE SAFETY & MAINTENANCE INFORMATION (See 7) · Don't expose the set, batteries, CDs to humidity, rain, sand or excessive heat. Don't use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. · Place the set on a hard and flat surface so that the system does not tilt. · The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. CD player and CD handling · If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. · Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. · To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. · Never write on a CD or attach any stickers to it. TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Do not open the set as there is a risk of electric shock! [. . . ] If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Do not open the set as there is a risk of electric shock!Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee. No sound /power ­ · ­ · ­ · Volume not adjusted Adjust the VOLUME Mains lead not securely connected Connect the AC mains lead properly Batteries exhausted/ incorrectly inserted Insert (fresh) batteries correctly dAtA indication ­ CD contains non-audio files · Press SEARCH or § once or more to skip to a CD audio track, instead of the data file The CD skips tracks ­ · ­ · CD damaged or dirty Replace or clean CD SHUFFLE or PROG is active Switch off SHUFFLE / PROG Severe radio hum or noise ­ Electrical interference: set too close to TV, VCR or computer · Move the set to increase the distance Poor radio reception ­ Weak radio signal · FM: Adjust the FM telescopic aerial nocd indication ­ · ­ · CD badly scratched or dirty Replace/ clean CD, see Maintenance Laser lens steamed up Wait until lens has cleared Remote control does not function properly (for AZ1325 model only) ­ · ­ · Batteries exhausted/ incorrectly inserted Insert (fresh) batteries correctly Distance/ angle between the set too large Reduce the distance/ angle nFcd indication ­ CD-R(W) is blank/ not finalized · Use a finalized CD-R(W) Environmental information We have done our best to reduce the packaging and make it easy to separate into 3 materials: cardboard, expandable polystyrene, polyethylene. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, exhausted batteries and old equipment. Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1. [. . . ]