User manual PHILIPS AZ1202

[. . . ] @ VOLUME ­ adjusts volume level # CD Display ­ shows CD functions 3 · Back panel ^ Telescopic antenna - improves FM reception. & Headphone - 3. 5mm stereo headphone jack * Battery door - open to insert 6 x 1. 5V R-14/ UM2/ C-cells. ( AC MAINS - inlet for power cord. 1 Open the battery compartment and insert six batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "+" and "­" symbols inside the compartment. Replace the compartment door, making sure the batteries are firmly and correctly in place. [. . . ] When inserting new batteries, do not try to mix old batteries with the new ones. Using AC power · · · 1 Check if the power/mains voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. Basic functions Basic functions 1 Switching on/off the set: 1 2 To switch on, adjust the source selector to CD, RADIO or TAPE/OFF as desired. To switch off, adjust the source selector to TAPE/OFF and check the cassette keys are released. Adjusting volume and sound Adjust the sound with the VOLUME and DBB (Dynamic Bass Boost) controls. Selecting sources Adjust the source selector to CD, RADIO or TAPE/OFF to select and toggle between sound sources. Adjust the band selector to LW, MW or FM to select your desired waveband. To switch off the radio, adjust the source selector to TAPE/OFF and check the cassette keys are released. CD Player Playing a CD This CD player plays Audio Discs including CD-Recordables and CD-Rewritables. (See 2) To open the CD door, lift the CD door at the edge marked LIFT TO OPEN. Insert a CD or CD-R(W) with the printed side facing up and press the CD door gently close. 2 1 Selecting a different track During playback, · Briefly press SEARCH or § once or repeatedly until you find your desired track. The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. Maintenance CD player and CD handling (See 7) · If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Never write on a CD or attach any stickers to it. · · · · · · Tape deck maintenance (See 7) To ensure quality recording and playback of the tape deck, clean parts A, B and C as shown, once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. Cleaning of the heads can also be done by playing a cleaning cassette through once. · Environmental information All unnecessary packaging material has been omitted. The packaging can be easily separated into three materials: cardboard, polystyrene and plastic. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, dead batteries and old equipment. Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1. [. . . ] If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. Note:The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere. How to connect a plug The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L). As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows: · Connect the blue wire to the terminal marked N or coloured black. [. . . ]