User manual PARTNER GBV 325 REV 2

[. . . ] GB INSTRUCTION MANUAL IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. FR MANUEL D'INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS: Avant d'utiliser cet appareil, veuillez lire attentivement les instructions et assurez-vous de les avoir comprises. Conservez les instructions pour référence ultérieure. DE BETRIEBSANWEISUNG WICHTIGE INFORMATION: Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen verstanden haben und gut aufbewahren. ES MANUAL DE INSTRUCCIONES INFORMACIÓN IMPORTANTE: Lea atentamente las instrucciones y asegúrese de entenderlas antes de utilizar esta aparato. [. . . ] Align the rib on the upper blower tube with the groove in the blower outlet; slide the tube into place. NOTE: The tube clamp bolt must be loose enough to allow blower tube to be inserted in blower outlet. Blower Outlet ASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. Always disconnect the spark plug before performing maintenance or accessing movable parts. WARNING: If received assembled, repeat all steps to ensure your unit is properly Groove Rib 2. Align the slots on the lower blower tube with the tabs on the upper blower tube. -- 4 -- Upper Blower Tube Lower Blower Tube Tube clamp bolt and nut NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube, and the rib on the elbow tube is on the bottom. Turn the lower blower tube clockwise until a click is felt to secure the lower blower tube to the upper blower tube. NOTE: When the upper and lower blower tubes are assembled together properly, the arrows on both tubes will be aligned. 5. To remove the tubes, turn the bolt counterclockwise to loosen the tubes (do not remove nuts); remove the tubes. HIGH-SPEED NOZZLE ASSEMBLY When greater air speed is desired, use the high-speed nozzle. Push lower vacuum tube into upper vacuum tube until the lower tube is securely seated in the upper tube (about 7 cm). Slanted end of lower vacuum tube 7. When vacuum tubes are fitted together, locate the label on the lower portion of the upper tube. Lower Vacuum Tube Upper Vacuum Tube -- 6 -- OPERATION OPERATING POSITION Hearing Protection Hearing Protection BEFORE STARTING ENGINE Eye Protection WARNING: Be sure to read the fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Contact an authorized service dealer. FUELING ENGINE Blower Vacuum WARNING: Remove fuel cap slowly when refueling. Before operation, petrol must be mixed with a good quality 2-cycle air-cooled engine oil. A 40:1 ratio is obtained by mixing 5 liters of unleaded petrol with 0, 125 liter of oil. Always read and follow the safety rules before fueling your unit. IMPORTANT Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. OPERATING TIPS S While vacuuming or blowing debris, hold the unit with the muffler side facing away from your body and clothes (see OPERATING POSITION). S To reduce the risk of hearing loss associated with sound level(s), hearing protection is required. S To reduce the risk of injury associated with contacting rotating parts, stop the engine before installing or removing attachments. [. . . ] Adjustments may be necessary if you notice any of the following conditions: S Engine will not idle when the throttle is released. Idle Speed Adjustment Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow). S Turn idle speed screw clockwise to increase engine speed if engine stalls or dies. Idle Speed Screw REPLACE FUEL FILTER To replace fuel filter, drain unit by running it dry of fuel, then remove fuel cap/retainer assembly from tank. [. . . ]