User manual PARTNER BV24 BLOWER/VAC

[. . . ] BV24 GB INSTRUCTION MANUAL IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. FR MANUEL D'INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS: Avant d'utiliser cet appareil, veuillez lire atentivement les instructions et assurez--vous de les avoir comprises. Conservez les instructions pour référence ultérieure. DE BETRIEBSANWEISUNG WICHTIGE INFORMATION: Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen verstanden haben und gut aufbewahren. ES MANUAL DE INSTRUCCIONES INFORMACIÓN IMPORTANTE: Lea atentamente las instrucciones y asegúrese de entenderlas antes de utilizar esta aparato. [. . . ] 13. Blower tube Elbow tube Vacuum bag Lower vacuum tube Upper vacuum tube Instruction manual 13 ASSEMBLY CARTON CONTENTS Check carton contents against the following list. S Blower S Blower tube S Upper vacuum tube S Lower vacuum tube S Elbow tube S Vacuum bag NOTE: It is normal for the fuel filter to rattle in the empty fuel tank. D A standard screwdriver is required for assembly. BLOWER TUBE ASSEMBLY 1. Align the rib on the blower tube with the groove in the blower outlet; slide the tube into place. NOTE: Knob must be loose enough to allow blower tube to be inserted in blower outlet. Blower Blower Outlet Tube ASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. Always disconnect the spark plug before performing maintenance or accessing movable parts. WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on the unit. Groove Rib 2. To remove the tube, turn the knob counterclockwise to loosen the tube; remove the tube. VACUUM BAG ASSEMBLY 1. Push the small end of the elbow tube through the small opening in the bag. -- 4 -- Elbow Tube Small Opening 4. Hold the vacuum inlet cover open until upper vacuum tube is installed. Vacuum Inlet Zipper Opening Retaining Post Rib Vacuum Inlet Cover 5. Place the hooks of the upper vacuum tube on the retaining posts of the unit. Pivot the tube until it is secured to the blower unit by the vacuum inlet latch. PIVOT Rib NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube, and the rib on the elbow tube is on the bottom. Turn knob clockwise to secure elbow tube. Hook Retaining Post VACUUM TUBE ASSEMBLY 1. Upper Vacuum Tube HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE 1. Remove the vacuum tubes by inserting the tip of a screwdriver into the latch area of the vacuum inlet. Gently tilt handle of screwdriver toward the back of the unit to release the latch while pulling up on the upper vacuum tube with your other hand. Insert the tip of a screwdriver into the latch area of the vacuum inlet. Gently tilt the handle of the screwdriver toward the back of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand. 3. Reinstall the blower tube (see BLOWER TUBE ASSEMBLY). -- 5 -- SHOULDER STRAP ADJUSTMENT (for vacuum use only) 1. [. . . ] Fuel Line CLEAN AIR FILTER Air Filter Cover Fuel Filter CHECK MUFFLER MOUNTING SCREWS Once each year, ensure muffler mounting screws are secure and tightened properly to prevent damage. Mounting Screw Holes Muffler Cover Air Filter Screws Screws Cleaning the air filter: A dirty air filter decreases engine performance and increases fuel consumption and harmful emissions. Always clean after every 5 hours of operation or yearly, whichever comes first. Clean the cover and the area around it to keep debris from falling into the carburetor chamber when the cover is removed. [. . . ]