User manual PALSONIC TFTV510

[. . . ] Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the the manufacturer's instructions are followed. 2 Cautions for safety (continued) Cautions for safety Unplug this product from the wall outlet before cleaning. Do not place the product on an unstable trolley, stand, tripod or table. [. . . ] The elevation can be adjusted from -50 to +150. 150 -50 10 Installation (continued) Connecting video/audio equipment Connecting video/audio equipment Composite VIDEO Signal Connection (RCA) Connect the composite signal terminal on the TV to the output of AV equipment through composite cable as illustrated. If you select the video signal, please set the input signal source to AV mode (please refer to page 13). To video input Y To video output Y VCR, DVD etc. w R w R To audio inputs To audio outputs Y W R AUDIO IN PHONE SPEAK OUT TUNER POWER IN Yellow (video) White (audio, L) Red (audio, R) Back panel S-VIDEO Signal Connection Connect the S-video terminal on the TV to the output of AV equipment through S-video cable as illustrated. If you select S-video signal, please set the input signal source to S-video mode (please refer to page 13). 11 1. Carefully check the terminals for position and type before making any connections. Make sure that all connectors are securely inserted into their terminals. When connecting an external device, turn off the power of the main unit first to prevent any possible damage. To S-VIDEO input w R To S-VIDEO output w R VCR, DVD etc. To audio inputs To audio outputs W R White (audio, L) Red (audio, R) AUDIO IN PHONE SPEAK OUT TUNER POWER IN Connecting the PC input terminals Connect the D-sub signal terminal on the TV to the output of PC equipment through Min D-sub 15 pin cable as illustrated. Connect a cable, which matches the audio output terminal on the computer. If you select PC signal, please set the input signal source to PC mode (please refer to page 13). To VGA input To VGA output To audio input To audio output Equipment with VGA output Notes: 1. If the signal resolution exceed the native resolution, it may not be possible to show fine detail with sufficient clarity. (This item is available only in NTSC) To adjust picture's backlight (Nature, Bright, Soft). Bright Press MENU button Press MENU button twice Blue Background Disable Language Color Sys Sound Sys Sound Set English Auto B/G To select the screen to display blue background or not when no signal inputs. Bass 6 To adjust the Bass Treble 9 To adjust the Treble Press MENU button Press MENU button third time Auto search Fine tuning Channel search Skip setting Channel edit To start auto search. To exchange current channel with the selected target channel. Note: In AV or S-Video mode, the menu is not accessible. Press MENU button in PC mode 50 Bright Contrast 50 Horizontal 50 Vertical 50 9 Phase Frequency 1334 9300K Color Bright Backlight To adjust picture's bright and contrast in PC mode. (not affect picture in TV or AV mode) If VGA input signal is not standard, you can adjust these two items until proper picture position is obtained. If the best picture can not be obtained after many times of auto correction, you can adjust these two items to obtain the best picture. To adjust colour temperature between 9300K 7300K 6500K, 5000K and User. (Nature, Bright, Soft) Note: In PC mode, only this menu can be accessed. 14 Operations in TV mode Channel preset Auto search/Channel search/Fine tuning/Skip setting Auto search 1 SOURCE Press MENU button third times to access menu (Refer to Menu introduction on page 14). Press VOL+/- buttons to start Auto search and all active programs will be memorised. During the process of Auto Search, pressing MENU button can stop Auto Search. MENU CH VOL POWER 2 3 Auto search Fine tuning Channel search Skip setting Channel edit CHMENU CH+ VOLVOL+ Channel searching . . . VHFH 5 If desired channel can not be preset by Auto search or if you would like to preset channels to specific position numbers one by one, use Channel search function. DIGIT Channel search 1 CH+ Press DIGIT buttons or CH+/buttons to select desired channel number. Press MENU button third times to enter into menu (refer to Menu introduction on page 14). Press VOL+/buttons to access the sub-menu, then press VOL+/- to start Channel search. Auto search Fine tuning Channel search Skip setting Channel edit 2 VOL+ CH- VOLMENU 3 Channel searching . . . VHFH 0 Pressing MENU button can exit Channel search sub-menu. 15 To conduct the following operation, you must select TV input signal (Refer to Selecting input signal on page 13). Fine tuning 1 SOURCE Press DIGIT buttons or CH+/buttons to select the desired channel. Then press VOL+/- to start Fine tuning to obtain best picture and sound. MENU CH VOL POWER Auto search Fine tuning Channel search Skip setting Channel edit 2 CHMENU CH+ VOLVOL+ 3 Fine Tuning VHFH 5 Skip setting 1 2 5 8 0 3 6 9 After Channel preset, You can skip unwanted channels by using this function. DIGIT 4 7 1 2 VOL+ CH- Use DIGIT buttons or CH+/- buttons to select an unwanted channel. To restore the skipped channel, please select the skipped channel by DIGIT buttons and then access the Skip Set sub-menu to set skip to save. Auto search Fine tuning Channel search Skip setting Channel edit CH+ VOLMENU 3 Skip Set VHFH 4 Skip 4 Skip Set VHFH 4 Save 16 Operations in TV mode (continued) Channel preset Channel edit Channel Edit After Auto Channel Preset, this function is for you to edit the order of programs conveniently according to your favourite. SOURCE MENU CH VOL POWER 1 Use DIGIT buttons or CH+/buttons to select current channel number. CHMENU CH+ VOLVOL+ Auto search Fine tuning Channel search Skip setting Channel edit 2 Press MENU button third times to access menu (refer to Menu introduction on page 14). 3 DIGIT Press CH+/- buttons to select Channel edit item. [. . . ] When the input signal is correct, press MENU button and it will display PC menu. 25 Picture adjustment 1 2 3 Press MENU button to access the menu. Press VOL+/- buttons to adjust the item. SOURCE MENU CH VOL POWER 50 Bright Contrast 100 Saturation 80 Sharpness 3 Color Hue Backlight Bright CHMENU CH+ VOLVOL+ Item Function Remarks Brightness Adjusting the brightness To adjust picture's bright and contrast in PC mode (does not affect picture in TV or Contrast Adjusting the contrast AV mode). If VGA input signal is not Horizontal Adjusting horizontal position standard, you can adjust these two items until proper picture Vertical Adjusting vertical position position is obtained. Phase Adjusting phase If the best picture can not be obtained after many times of auto correction, you can adjust these two items to obtain the best picture. [. . . ]