User manual ORBIT IRRIGATION 62015-91600

[. . . ] 6 station products are fitted with 6 station terminals & show 6 stations on the display. Note: Always check local plumbing and electrical codes for requirements when installing the timer, transformer, and sprinkling system. Use only with household current with an appropriate transformer matching your voltage and plug type. Help Before returning this timer to the store, contact Orbit®´Technical Service at: 1-800-488-6156. Listings The timer is tested to UL-1951 standard and is ETL® listed. [. . . ] The wire can be buried in the ground; however, for more protecCommon Wires Solenoids tion, wires can be pulled through PVC pipe and buried underground. Be careful to avoid burying the wires in locations where they could be disturbed by digging Valves or trenching in the future. All of the common wires for all the valves can be connected together to one common wire going to the timer. The other valve wire is to be connected to the specific station wire that is to control that valve. All wires should be joined together using wire nuts, solder, or vinyl tape. For additional protection to waterproof connections, a WaterMaster® grease cap can be used. To avoid electrical hazards, only one valve should be connected to each station. Do not use solenoids that exceed these values. 1 2 Installation Connecting Valve Wires to the Timer 1. Connect each valve wire to its station terminal (labeled 1-6) by inserting the bare wire. Connect the common wire to the terminal screw labeled "COM". Install 2 AA (1. 5 volt) alkaline batteries in the battery compartment. Press CLEAR to make the highlighted day a non-watering day. S T1 A2 R3 T ZONE 1 2 3 4 MAN. DURATION M T W Th F S Su 2nd 3rd EVERY SET WATERING DAYS Transformer Figure 5 WARNING: Do not link two or more timers together using a common transformer. Slide the cover back on until it snaps. 3 4 5 Programming Step 5 -- Setting Periodic Watering Schedule Manual Operation The WaterMaster® Timer provides 2 separate manual settings. These manual settings will not alter the automatic setting during or after use. All Stations Cycle Once Reviewing / Changing Settings To Change Time and Current Day Instead of selecting a particular day (or days) of the week, you may choose to water every second day or every third day. Note: If you have selected days of the week in step 4 you cannot select every 2nd or 3rd day watering also. Press CLEAR until blinking indicator is pointing to either 2nd or 3rd day as desired. (See Figure 11. ) The blinking indicator steps to the other selection. S T1 A2 R 3 T ZONE 1 2 3 4 M T W Th F S Su 2nd 3rd EVERY 1. Follow programming instruction in Programming section "Step 1. " To Review Start Times SET WATERING DAYS MAN. Display M T W Th F S Su 2nd 3rd shows ALL, solid over stations with proS T1 grammed durations, and over MANUAL. The timer will automatically water all assigned stations in sequence for Figure 13 the time assigned to each (a water droplet drawing will appear on the display) and then shut off and return to the automatic mode. One Station Watering EVERY 1. To make changes, press + or ­ for any Start Time and follow instructions in Step 2 of "Programming. " To Review Watering Durations 1. [. . . ] Timer will water for the desired duration and return to the automatic mode. Turn dial to SET WATER DURATION. To make changes, press + or ­ for any station duration and follow instructions in Step 3 of "Programming. " To Review Watering Days: 1. To make changes, press CLEAR on any day or schedule (to skip to the next day press NEXT. ) Follow instructions in Step 4 and/or Step 5 of "Programming. " Note: When watering begins, the display will show a water droplet and will count down the programmed time on the display. To discontinue watering in the manual mode, press CLEAR. Note: After MANUAL has been pushed, if ENTER is not pushed within 10 seconds, the display will return to Time of Day. 6 7 8 Other Features / Default Stop the Automatic Watering for 24 hours 1. [. . . ]