User manual OPTOMA PK102

[. . . ] Disconnect the battery if the product is not being used for a long period of time. Do not expose the battery to temperatures above +60°C (+140°F) 13. Physical damage/abuse would be (but not limited to): Unit has been dropped. Opening or removing covers may expose you to dangerous voltages or other hazards. [. . . ] Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this device. Operation conditions This device complies with Part 15 of the FCC Rules. this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. DISpoSal of olD electrIcal & electronIc equIpment (Applicable throughout the European Union and other European countries with separate collection programs) This symbol found on your product or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate disposal of this product. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. Notice: Canadian users Remarque à l'intention des utilisateurs canadiens Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries · EMC Directive 2004/108/EC (including amendments) · Low Voltage Directive 2006/95/EC · R & TTE Directive 1999/5/EC (if product has RF function) 2 proDuct overvIeW 1. DC Input 11 13 2 3 4 FOCUS 8 9 6 7 10 12 1 14 package overvIeW 1 7 10 InStallIng the Battery 1 2 AV IN 5 VGA \ USB IN 2 8 11 3 4 3 9 12 1. Insert battery with electrical contacts facing downward and away from lens. Slide the battery cover back into place over battery pull tab. (~) VOLUM OL E CONTR 13 5 4 5 6 <Note> The standard accessories may vary in each region due to different applications. Standard Accessory 1. USB to DC jack cable 6 7 3 ChargIng the Battery 1 2 connect input source - (vIDeo In) 1. The indicator will flash red when no battery is installed. VOLU ME CON TRO L AV IN FOCU S 1 1. Connect to external speaker using AVII cable (optional) and use the toggle to disable/enable the PK102 internal speaker ( ) <Note> 1. All other brand and product names are trademarks or registered trademarks of their respective companies. The connecting cable of video output device is not supplied, please contact their service center. Using with device with audio signal voltage > 0. 3Vrms is not recommended. 2 VG A\ US B IN DC IN 3 or 1 AV IN FOCU S 4 2 5 1 VG A\ US B IN DC IN VOLU ME CON TRO L or AV IN AV IN FOCU or S FOCU S iPod 1 <Optional> The PK102 can also be charged via USB to DC cable ( ) MOLE X MOLE X 2 2 VGA \ USB IN DC IN connect input source - (vga/uSB/component In) 1. Insert universal connector with arrow mark facing up. <Note> Supported formats VGA: 640x480@60Hz, 800x600@60Hz connect input source Data tranSfer 1. Connect laptop or PC for data transfer to the PK102 internal memory using supplied Male USB Cable <Note> The laptop/PC can only detect the input source when the PK102 is switched on. [. . . ] Battery is at mid capacity Battery is at low capacity VGA source Image setting, you can adjust Frequency, Phase and H. Position: adjust the horizontal position. <Note> Only for VGA input source. trouBleShootIng If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. Image Problems No image appears on-screen · Ensure the cables/charger/ battery are correctly and securely connected. [. . . ]