User manual NORTHSTAR NAVICO NAIS-300 REV 1.0

[. . . ] When connected to a compatible chart plotter, it will provide a representation of the position and movements of all AIS equipped vessels within VHF range The advantages of the NAIS-00 are: · Increased awareness of the current shipping situation within your VHF range through the exchange of data between vessels. Improving traffic management in busy shipping lanes through exchanging information between vessels and shore based traffic stations. Reporting information automatically in shipping areas where it is mandatory. · · As with all electronic navigational equipment, it is only an aid to navigation and should not be used as a substitute for good seamanship. Remember - Maritime law requires that you keep a good lookout at all times. Introduction 5 1. 2 SimNet/NMEA2000 SimNet is Navico's proprietary high speed data bus network compatible with NMEA000. [. . . ] Pull the splash cover off of the SimNet/NMEA000 socket, ensure the connector on the end of the cable is in the correct orientation and press firmly into the socket. SimNet (300-N model only) With the supplied cable connected to the NAIS-00, connect the other end into the vessels SimNet network. Installation 9 NMEA2000 (300-L model only) With the supplied cable connected to the NAIS-00, connect the other end into the supplied T-connector, then connect this into the vessels NMEA000 network. 2. 5 NMEA0183-HS (RS232 supplied) This data cable is used to connect the NAIS-00 to a PC or laptop in order to configure it, and for AIS enabled PC chartplotter applications. For further information regarding the wiring of this cable please refer to chapter . 2. 6 NMEA0183-HS (RS485 not supplied) This data cable is used for connectivity to AIS enabled chart plotters and other marine equipment with an NMEA018-HS interface. For wiring information, refer to Figure . 1. (NMEA0183-HS is specified at 38. 4kbaud and is not compatible with conventional NMEA0183, which operates at the lower speed of 4800baud) 2. 7 Transmit disable switch (not supplied) Any momentary action, push to make switch can be used. Take a wire from each terminal of the switch and wire them into the connector. Because there is negligible current drawn through this cable, any suitable two core cable will do, providing it forms a good seal once inserted in the grommet. Refer to section 4. . 2. 8 GPS antenna The antenna, ideally needs to be mounted as low as possible with a clear view of the sky to minimise errors due to movement over and above the transitory movement of the vessel. The GPS antenna is capable of being flush mounted on a suitable flat area of the cabin roof or deck area. In this configuration, fit the supplied rubber gasket under the antenna and use the four threaded studs, nuts and washers to fix the antenna down. 10 Installation The cable can be routed in the molding to drop down directly underneath, or by breaking out the thin traps, the cable can be routed out of the side of the antenna. Alternatively, the antenna may be fixed on a standard 1" threaded mounting pole (Not supplied). Attach the supplied mounting base to the antenna with the four screws, thread the cable down the center hole and through the pole. Thread the pole into the mounting base, before attaching the pole to the superstructure. To minimize interference, place the antenna in a position away from steel constructions, wires, metal masts, sources of electrical interference, such as radar etc. If installing the GPS antenna close to other antennas, mount it either above or below their radiation beams. BIIT Rx Tx The antenna cable is terminated in a screw fit connector (SMA). Push the antenna plug into the socket on the side of the unit and screw down the retaining collar. GPS Antenna VHF Antenna 73. 5mm 2. 9in Figure. 2. 3 - Antenna connections 210mm (8. 27in) 2. 9 VHF antenna (not supplied) North American Users - To meet FCC (Federal Communications Commission) rules on Radio Frequency Exposure, it is recommended that the VHF antenna is mounted at least 3m (10ft) away from any area accessible to any personnel on board. If this distance is achieved by vertical separation, the antenna must be at least 5m (16. 5ft) above deck. Failure to observe these recommendations may expose those within the MPE (Maximum Permitted Exposure) radius of 1m (3ft) to RF absorption levels that exceed the FCC safe limits. Installation 11 NAIS-300 PWR The most important factor in the performance of any AIS transceiver will be the quality and positioning of the antenna. As the range of VHF signals are governed by line of sight, the antenna should be placed as high as possible, while remaining clear of any metallic objects. Long whip antennas are generally recommended for larger boats, although the most popular antennas for marine use is 1m (ft in) long. On sailboats these are usually mounted on the masthead, where the length of the antenna keeps it clear from the navigation lights and wind vanes. This type of antenna can also be mounted on the cockpit roof or powerboat garages. For maximum range, it is recommended that a VHF antenna specifically tuned for use with an AIS is used, and mounted away from the standard VHF antenna. [. . . ] HierbijverklaartNavicoASdathettoestelNAIS-300inovereenstemmingis metdeessentiëleeisenendeandererelevantebepalingenvanrichtlijn1999/5/ EG. Parlaprésente, NavicoASdéclarequeceNAIS-300estconformeauxexigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables. HärmedintygarNavicoASattdennaNAIS-300ståriöverensstämmelsemed deväsentligaegenskapskravochövrigarelevantabestämmelsersomframgårav direktiv1999/5/EG. Undertegnede Navico AS erklærer herved, at følgende udstyr NAIS-300 overholderdevæsentligekravogøvrigerelevantekravidirektiv1999/5/EF. [. . . ]