User manual NIKE TRIAX SPEED

[. . . ] The counting continues. Note: If you want to save the times for your most recent run, cycle to the next run. If you want to erase the times for your most recent run, reset the run. 7 START/LAP MODE STOP/NEXT RUN NUMBER STOP MARK SPLIT ELECTROLITE Run - A run is an exercise session consisting of any number of consecutive lap time measurements. Lap - Lap time is the time required to cover a given segment of a run. Split - Split time is the total elapsed time in a run up to the completion of a lap. Start measuring a lap Press the START/LAP button. [. . . ] Split - Split time is the total elapsed time in a run up to the completion of a lap. Start measuring a lap Press the START/LAP button. The lap/split time display begins with 1/100 seconds, then seconds, then minutes. If the accumulated times in a run proceed to hours, the elapsed hours appear above the primary display and replace 1/100 seconds in the secondary display. Cycle to the next run The chronograph must be stopped to cycle to the next run. Your Triax watch will record the next lap times as part of a new run. EN Manual FINAL (RunII) NEW 4/26/99 5:00 PM Page 8 8 b DATA In DATA mode you can recall lap and split times measurements from your saved runs. RUN NUMBER 9 Reset a run The chronograph must be stopped to reset a run. Time returns to zero. NOTE: Over 100 hours, the run will be reset automatically. A DJ U S T /R E S E T S TA R T /L A P MODE S TO P /N E XT Switch the primary display between lap and split time In CHRONOGRAPH mode, press the ADJUST/RESET button. Lap and split times will change between primary and secondary position on the display. Note that display settings in CHRONOGRAPH mode are also reflected in DATA mode. D AT E ELECTROLITE Cycle through the run numbers Press the STOP/NEXT button. Run number and date of run are displayed. NOTE: If dashes appear in the display, no data exists for that run. Check remaining memory capacity When the chronograph is reset, press the STOP/NEXT button. Lap memory capacity is displayed. Cycle by date through lap and split times, total time, best time, and average time for each run Press the START/LAP button. EN Manual FINAL (RunII) NEW 4/26/99 5:00 PM Page 10 10 c TIMER TIMER mode provides a programmable countdown interval timer. Set unused segments to zero. A D J U S T /R E S E T 11 Erase data for an individual run Press the STOP/NEXT button to select a run that you want to delete. "HOLD CLEAR" flashes, and you will hear a confirmation tone, then the data for the selected run is erased. NOTE: When you delete a run the next run takes its place. The next alarm number appears at the bottom of the display. 5 Press the MODE button to cycle to the next adjustable value. 6 Repeat steps 3-5 until you have set all values: hour, minutes, time zone. Turn all alarms off Press and hold the STOP/NEXT button for 4 seconds. "HOLD ALL OFF" flashes and all alarms turn off. EN Manual FINAL (RunII) NEW 4/26/99 5:00 PM Page 20 f TIME In TIME mode you can set the time and calendar information for two time zones. NOTE: Press and hold the MODE button for one second in any mode for quick return to TIME mode. TIME ZONE 20 21 ADJUST/RESET S TA R T / L A P MODE 3 Press the MODE button to cycle to the next value. S TO P / N E X T 4 Press the START/LAP button to increase the flashing value. TIME ELECTROLITE DAY/MONTH DATE 5 Press the STOP/NEXT button to decrease the flashing value. Set time of day and calendar 1 Press and hold the ADJUST/RESET button for two seconds. "HOLD ADJUST" flashes in the display, then the time and time zone appears. The seconds indicator flashes. NOTE: Under thirty seconds the value resets to zero. Over thirty seconds, minutes advance. 6 Repeat steps 3-5 until you have set all values: seconds, hours, minutes, day, month, year, 12 or 24-hour clock, and day/date or month/date display. 7 Press the ADJUST/RESET button to save the changes. 2 Press the START/LAP or STOP/NEXT button to reset the seconds. EN Manual FINAL (RunII) NEW 4/26/99 5:00 PM Page 22 22 g DEMO In DEMO mode you can display a brief view of functions within each mode. 23 Switch between time zones 1 In TIME mode, press and hold the STOP/NEXT button. The alternate time zone time-of-day information appears. ADJUST/RESET S TA R T / L A P MODE 2 Release the button when time zone indicator stops flashing. S TO P / N E X T 3 Follow the preceding instructions to set the time and calendar information for the alternate time zone. ELECTROLITE Hold the STOP/NEXT button for fewer than 3 seconds for a brief display of alternate time zone information. Turn the confirmation tone on and off Press the START/LAP button. The symbol toggles on and off each time the button is pressed. NOTE: Press and hold the MODE button for one second in any mode for quick return to TIME mode. Activate DEMO mode DEMO mode is accessed through TIME mode. In TIME mode, press and hold the START/LAP and STOP/NEXT buttons simultaneously. [. . . ] The alternate time zone time-of-day information appears. ADJUST/RESET S TA R T / L A P MODE 2 Release the button when time zone indicator stops flashing. S TO P / N E X T 3 Follow the preceding instructions to set the time and calendar information for the alternate time zone. ELECTROLITE Hold the STOP/NEXT button for fewer than 3 seconds for a brief display of alternate time zone information. Turn the confirmation tone on and off Press the START/LAP button. The symbol toggles on and off each time the button is pressed. NOTE: Press and hold the MODE button for one second in any mode for quick return to TIME mode. Activate DEMO mode DEMO mode is accessed through TIME mode. In TIME mode, press and hold the START/LAP and STOP/NEXT buttons simultaneously. The watch will cycle through the modes, briefly demonstrating the functions of each. [. . . ]