User manual NIKE AMBIENT ALPINE

[. . . ] If no buttons are pressed for 2-3 minutes the watch will exit ADJUST mode and return to TIME mode. To quickly exit ADJUST mode, press BUTTON A repeatedly to cycle through all adjustable elements; the display will then stop blinking. 3 Press BUTTON B to advance one minute. Hold for quick advance. 4 Press BUTTON A to advance to next programmable element. [. . . ] The alternate temperature measurement appears (Cº/Fº). 1 Determine the actual temperature. After 2 seconds there is a tone related to changing the display between C° and F°. To quickly exit ADJUST mode, press BUTTON A repeatedly to cycle through all adjustable elements; the display will then stop blinking. 2 Hold BUTTON A for fewer than 2 seconds for brief glimpse of alternate temperature measurement (C°/F°). EN Manual FINAL (Ambient) NEW 4/26/99 5:04 PM Page 14 14 15 3 Press BUTTON B to advance the blinking digit to the desired temperature. Reset the thermometer so there is no offset In TEMPERATURE mode, press and hold BUTTONS A and B for 4-5 seconds. The offset will be erased. 4 Press BUTTON A The degree indicator blinks. 5 Press BUTTON B to advance the blinking digit to the desired temperature. 6 Press BUTTON A to save changes. Temperature is set and no elements are blinking. EN Manual FINAL (Ambient) NEW 4/26/99 5:04 PM Page 16 d TEMPERATURE ALARM In TEMPERATURE ALARM mode, you can set an alarm to sound when the temperature crosses a certain point. C 16 17 CROWN B A Note that the adjustable element is always blinking. If no buttons are pressed for 2-3 minutes the watch will exit ADJUST and return to TEMPERATURE ALARM mode. To quickly exit ADJUST mode, press BUTTON A repeatedly to cycle through all adjustable elements; the display will then stop blinking. 3 Press BUTTON B to advance 1/10th degree. Hold for quick advance. Set the temperature alarm 1 Decide at what temperature you want to be alerted. 4 Press BUTTON A to advance to next programmable element. The degree indicator begins blinking. 2 In TEMPERATURE ALARM mode, press and hold BUTTON A for 2-3 seconds. The 1/10th degree indicator blinks. 5 Press BUTTON B to advance one degree. Hold for quick advance. EN Manual FINAL (Ambient) NEW 4/26/99 5:04 PM Page 18 18 e COUNTER In COUNTER mode you can count in positive increments from 1 up to 999. C 19 6 Press BUTTON A to save changes. C R OW N B A 7 The temperature alarm is set when no elements are blinking. Turn the temperature alarm ON/OFF In TEMPERATURE ALARM mode, press BUTTON A. Note: The temperature alarm turns itself off automatically when the temperature rises or falls across the selected temperature and the alarm has sounded for ten seconds. The temperature alarm will also turn off after 12 hours, to conserve battery power. Increase count by one In COUNTER mode, press BUTTON A. Reset to zero In COUNTER mode, press and hold BUTTON A. Counter returns to zero. EN Manual FINAL (Ambient) NEW 4/26/99 5:04 PM Page 20 f TIMER TIMER mode provides an adjustable countdown timer. Tone sounds once if timer is set for less than a minute, 5 times if timer is set for more than one minute. C 20 21 CROWN 2 Press BUTTON B to advance one minute. Hold for quick advance. B A 3 Press BUTTON A to advance to next programmable element. The seconds begin blinking. Set the timer 1 In TIMER mode, press and hold BUTTON A for two seconds. If no buttons are pressed for 2-3 minutes the watch will exit ADJUST and return to TIMER mode. [. . . ] After approximately 4 hours the watch will enter TIME mode to conserve battery power. All other modes - When TEMPERATURE ALARM is activated sampling interval is 10 minutes. When TEMPERATURE ALARM is not activated, sampling interval is 1 hour. Activate the Electrolite display feature Press BUTTON C to illuminate both the analog and digital displays for 3 seconds. H2O Resistance 50 Meters MATERIALS CASING STRAP CASEBACK Polycarbonate FRESH:Stretchable acrylic/Polyester FROZEN: Polyurethane Stainless Steel Note: Irregular movements of the second sweep hand indicate the battery needs to be replaced. [. . . ]