User manual NEWPOL XV120EL

[. . . ] Improper use of the appliance can lead to personal injury and material damage. READ AND SAVE THESE INSTRUCTIONS This appliance is designed to vent cooking smoke and odors only. Be certain your appliance is properly installed and grounded by a qualified technician. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. [. . . ] The lighting can be used independently of the fan. i On/Off button j Fan power level buttons Four fan speed selection. k Delayed Shut Down This button activates the Delayed Shut Down feature. The fan can be set to turn off automatically after either 5 or 15 minutes. l Grease filter button The indicator next to the grease filter button lights when the grease filters need to be cleaned. This button is also used: ­ to reset the grease filter timer after cleaning the grease filters (see "Cleaning and Care"). ­ to show how long the grease filter has been in use (see "Operation / Grease filter timer"). ­ to change the number of hours counted by the grease filter timer (see "Operation / Reprogramming the grease filter timer"). 9 Operation Main power switch Intensive setting Level "4" (yellow indicator) should be used for a short period when frying or cooking food with a strong aroma. If the appliance is not going to be used for a long period of time (e. g. while vacationing) turn the appliance off by pressing the main power switch to "0". The next time it is turned on, the hood will operate at the level previously used. Factors such as narrow duct diameter and bends will affect this value. Level 1 operates at 40% capacity Level 2 operates at 60% capacity Level 3 operates at 80% capacity Level 4 operates at 100% capacity Turning on the fan Delayed Shut Down If odors or smoke remain in the kitchen after cooking has been completed, the Delayed Shut Down feature can be selected to allow the hood to continue running for either 5 or 15 minutes. ^ Press the On/Off button. The On/Off indicator lights. Selecting the power level ^ Press the Delayed Shut Down button while the fan is still running. Do not attempt to change the bulbs until they have had sufficient time to cool down. Fingerprints or body oils deposited on the bulb will decrease the life of the bulb. ^ Pull the old bulb, d, out of its socket and replace it with a new one. The glass is specially made to filter harmful light rays. 16 After Sales Service In the event of a fault which you cannot correct yourself please contact: ­ Your Miele Dealer or ­ The Miele Technical Service Department USA CDN 1-800-999-1360 techserv@mieleusa. com 1-800-565-6435 service@miele. ca When contacting the Technical Service Department, please quote the model and serial number of your appliance. These are shown on the data plate which is visible when the grease filter is removed. 17 18 Installation instructions Table of Contents Caring for the environment Structural support Electrical data Appliance dimensions Installation Air extraction 20 Caring for the environment Disposal of packing material The cardboard box and packing materials protect the appliance during shipping. Danger of suffocation! Disposal of an old appliance Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Before discarding an old hood, unplug it from the outlet and cut off its power cord to prevent hazards. 21 Structural support The ceiling mounting plate will support the weight of the hood. This ceiling plate must be attached to rigid structural framing that is supported in its entirety by the ceiling joists, or to the ceiling joists directly. Do not attach the plate directly to the ceiling by using anchors, mollies or toggle bolts. 22 Electrical data All electrical work should be performed by a qualified electrician in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. [. . . ] The S10 wall anchors included in the packaging are not for use in USA/CDN. Be certain that the ceiling is stable enough to support the hood. 26 Installation ^ Secure the ducting to the mounting plate using a hose clip. ^ Insert the short edge of two spring clips into their slots from below and position so that the tab faces the center of the mounting plate. ^ Insert the four countersunk screws M 6 x 20 into the recessed holes from above. Tape the screws from above to prevent them from being pushed upwards when the nuts are tightened. 27 Installation ^ Secure the mounting plate to the ceiling using the 8 x 60 lag bolts. [. . . ]