User manual NEWPOL XS 151EV

[. . . ] READ AND SAVE THESE INSTRUCTIONS This appliance is designed to vent cooking smoke and odors only. Be certain your appliance is properly installed and grounded by a qualified technician. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. [. . . ] The lighting can be used independently of the fan. k Grease filter button The indicator next to the grease filter button lights when the grease filter needs to be cleaned. This button is also used: ­ to reset the grease filter timer after cleaning the grease filter (see "Cleaning and Care"). ­ to show how long the grease filter has been in use (see "Operation / Grease filter timer"). ­ to change the number of hours counted by the grease filter timer (see "Operation / Reprogramming the grease filter timer"). h On/Off button i Fan power level buttons Four fan speed selection. j Delayed Shut Down This button activates the Delayed Shut Down feature. The fan can be set to turn off automatically after either 5 or 15 minutes. 9 Operation Turning on the fan Automatically switching back the intensive power level The intensive level "4" can be programmed to automatically switch back to level "3" after 10 minutes. ^ Turn the fan and the lights off. Selecting the power level ^ Press and hold the "Delay Shut down" button for 10 secs. ^ Use the "­/+" controls to select the desired power level. + = increases the fan speed ­ = decreases the fan speed Levels "1" to "3" (green indicators) are usually sufficient for normal cooking. Intensive setting Level "4" (yellow indicator) should be used for a short period when frying or cooking food with a strong aroma. ­ light ^ Press the following buttons one after another, ­ the "­" button, and ­ the light button again. 10 Operation Fan performance The maximum air flow capacity is 625 cfm. Factors such as narrow duct diameter and bends will affect this value. Removing the grease filter The grease filter should be cleaned every 3 - 4 weeks or whenever the grease filter indicator lights. Keep the grease filter clean to prevent a fire hazard. ^ To remove the grease filter pull the locking clip forward. Support the grease filter so that it does not fall onto the cooktop. 17 Cleaning and care Cleaning the grease filter ^ By hand: use a scrub brush with a solution of warm water and mild detergent. Do not use the pure detergent, aggressive all purpose cleaners, oven sprays, abrasive cleaning agents or limescale removers. ^ In a dishwasher: place the filter vertically in the lower basket, making sure that the spray arm is not blocked. Depending on the detergent, cleaning the grease filter in a dishwasher may cause permanent discoloration of the filter surface. ^ While the filter is removed, clean any dirt or grease from the interior casing to prevent the risk of fire. ^ When putting the grease filter back make sure that the locking clip is facing the cooking surface. ^ If the filter is incorrectly installed, insert a small screwdriver into the slit along its edge to disengage it from the casing. ^ After returning the grease filter, press the grease filter button for 3 seconds to reset the timer. ^ If the grease filter is cleaned before the grease filter timer has reached its maximum, the grease filter button should be pressed for 6 seconds to reset the counter to zero. 18 Cleaning and care Changing the light bulb Before changing the light bulbs, disconnect the hood from the power supply by either removing the fuse, unplugging it, or manually "tripping" the circuit breaker. When in use halogen bulbs become extremely hot, and can burn your hands. Do not attempt to change the bulbs until they have had sufficient time to cool. [. . . ] Please contact your local recycling center about the possibility of recycling these materials. Before discarding an old hood, unplug it from the outlet and cut off its power cord to prevent hazards. 23 Structural support The ceiling mounting plate will support the weight of the hood. This ceiling plate must be attached to rigid structural framing that is supported in its entirety by the ceiling joists, or to the ceiling joists directly. Do not attach the plate directly to the ceiling with anchors, toggle bolts, etc. 24 Electrical data All electrical work should be performed by a qualified electrician in strict accordance with national and local safety regulations. [. . . ]