User manual NEWPOL XF81408DG

[. . . ] appliance, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. If the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. ~ b) Before servicing or cleaning the ~ This appliance is intended for ~ This appliance complies with current safety requirements. [. . . ] ^ To activate the automatic switch back press the "+" button. ^ To deactivate the automatic switch back press the "­" button. ^ To save the setting press the On/Off button. 11 Cleaning and care , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before cleaning or servicing the hood, disconnect it from the power supply, see "Important Safety Instructions". Avoid: ­ cleaning agents containing soda, acids or chlorides, ­ abrasive cleaning agents e. g. ^ While the filter is removed, clean any dirt or grease from the filter casing to prevent the risk of fire. , A dirty filter is a fire hazard. ^ To remove hold and pull out the deflector and the grease filter together. Support the grease filter so that it does not fall onto the cooktop. 13 Cleaning and care Inserting / replacing the active charcoal filters For recirculation mode an active charcoal filter must be used in addition to the grease filter. The active charcoal filter is inserted above the grease filter. ^ To insert the grease filter, make sure that the red plastic guides are at the front and facing up. It should glide onto the fixing pins. ^ Replace the filter every 6 months or when it is no longer absorbing cooking odors. ^ Dispose of the charcoal filter with the household waste. 14 Cleaning and care Changing the light bulbs , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before changing the light bulbs, disconnect the hood from the power supply, see "Important Safety Instructions". When in use halogen bulbs become extremely hot, use caution. Do not attempt to change the bulbs until they have had sufficient time to cool. Fingerprints or body oils deposited on the bulb will decrease its life. ^ Pull the deflector out and remove the grease filter as described in "Cleaning and Care - Grease filter". c Installation kit for recirculation mode; contains air outlet grille, hose and hose clips (optional accessory) d Installation kit DML 300 to install a custom panel contains retractable brackets and screws ( optional accessory) 8 screws 3. 5 x 16 mm to anchor the ventilation hood in the cabinet. 8 screws M4 x 12 mm to anchor the ventilation hood at the runners. 4 screws could be used (alternatively to the plastic rivet) to fix the spacer bar. To avoid risk of hand or other injury, avoid contact with sharp edges during the assembly and installation process. , CAUTION 2 screws 4 x 30 mm to anchor the ventilation hood at rear wall. 4 plastic rivets to connect the space bar with the appliance rear wall. 25 Installation 26 Installation 1. Installing the space bar T = K cabinet depth minus G hood depth ^ The hood depth G depends on the custom panel: ­ a Hood installed with a cabinet matching custom panel ­ b Hood installed without front panel These measures are only valid for the installation if the front panel sits flush with the cabinet corpus (without the door). If the front panel should be installed recessed or flush with the cabinet door, adjust the measure T accordingly. Clip it with a knife at the predetermined breaking point of the next lower measure. ^ Screw the space bar flush with the wall under the cabinet side walls. ^ At the front edge of the spacer strip draw a vertical line on left and right side of the inside cabinet. 27 Installation 2. Do not remove the installation protector between the deflector and casing before the installation is completed. The runners are made for side walls of 5/8" (16 mm) and 3/4" (19 mm). Screw on the angled side which has the imprint of the respective cabinet wall measure. ^ Align the runners with the drawn line and be sure that they are flush with the lower edge of the cabinet side wall. ^ Hold the grease filter and pull it out along with the deflector. 28 Installation ^ Take the grease filter out and put it aside. ^ Push the deflector back in. ^ Insert the hood into the cabinet from below and until the spring clips click into place. [. . . ] ^ Install the Active Charcoal Filter (see "Cleaning and care"). 24 0 40 33 160 15 0 33 Air extraction , WARNING Danger of toxic fumes. Gas cooking appliances release carbon monoxide that can be harmful or fatal if inhaled. To reduce the risk of fire and to properly exhaust air, the exhaust gases extracted by the hood should be vented outside of the building only. Do not vent exhaust air into spaces within walls or ceilings or in attics, crawl spaces or garages. [. . . ]