User manual NAIM NAP 140

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NAIM NAP 140. We hope that this NAIM NAP 140 user guide will be useful to you.


NAIM NAP 140 : Download the complete user guide (3192 Ko)

Manual abstract: user guide NAIM NAP 140

Detailed instructions for use are in the User's Guide.

[. . . ] One end of each cable is marked with a band to establish its correct orientation. Naim loudspeaker cable is correct for your system and your dealer will make up leads to suit your equipment installation. The leads should each be at least 3. 5 metres long and of equal length. Loudspeaker leads are, like interconnect leads, directional, and should be connected so that the printed arrow points towards the speakers. [. . . ] Equipment must not be exposed to dripping or splashing and no objects filled with liquid, such as vases, should be placed on the equipment. Use of non-standard speaker cables or interconnects may invalidate your guarantee. 5 Connection 5. 1 mains lead As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured red. 5. 2 non-rewireable mains plugs If a non-rewireable plug is cut from a mains lead (for whatever purpose) the plug MUST be disposed of in a way to render it totally unusable. Considerable shock hazard exists if the cut-off plug is inserted into a mains outlet. 5. 3 fuse carrier Should the plug fuse carrier be damaged or lost, the correct replacement must be obtained from your dealer, or from Naim Audio direct. Do not use the plug until the fuse carrier is replaced. 5. 4 plug fuses Replace only with ASTA or BS 1362 approved fuses. NOTE This equipment has been tested and found to comply with the relevant EMC and Safety Standards, and, where applicable, also complies with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. THE VOLUME SHOULD BE REDUCED. 8. 3 loudspeaker cable and connectors Only Naim Audio speaker cable should be used to connect a loudspeaker to the output of the NAP 300. Custom Naim Audio loudspeaker connectors are supplied to make the connection. IN ORDER TO COMPLY WITH CURRENT EUROPEAN SAFETY REGULATIONS IT IS ESSENTIAL THAT THESE ARE USED. DAMAGE TO THE AMPLIFIER MAY RESULT IF "HIGH DEFINITION" CABLE OR ANY OTHER SPECIAL CABLE IS USED TO CONNECT THE LOUDSPEAKERS. 6 NAP 300 Connection & Specifications 9. 1 NAP 300 connection to NA PS300 Power Supply to preamp power supply. left, ch1 left speaker ch1 NA PS300 rear mains in Input Socket 1 Input Socket 2 ch1 -ve nc nc ch 2 -ve + 1 - + 2 right speaker ch2 to preamp power supply. right, ch2 9. 2 Specifications NAP 300 & NA PS300 Power Output Continuous, 8 ohms Transient Quiescent Power Consumption Voltage Gain Input Impedance Frequency response Mains Supply: Case size (H x W x D) NAP 300 NA PS300 Weight NAP 300 NA PS300 90 Watts per channel 500VA 27VA +29dB 18 kilohms -3dB @ 2Hz and 70kHz 100V. 230V - 50/60Hz 87 x 432 x 314mm 87 x 432 x 314mm 10. 7kg 14. 1kg 7 NAP 250 10 Installation and Operation The NAP 250 should be installed in its final operating location before connecting cables or switching on. Switch on the source and preamplifier components, with the volume turned down, before switching on the NAP 250. The NAP 250 is very heavy and care should be taken when lifting or moving it. Make sure that the surface it is to be placed on can support the full weight. 10. 1 connection notes The negative input and output connections are all common. The mains earth should always be connected regardless of what other equipment is used. [. . . ] Make sure that the surface they are to be placed on can support their full weight. 14. 1 connection notes The negative input and output connections are all common. The mains earth should always be connected regardless of what other equipment is used. This only grounds the case and the electrostatic screen within the transformer, and is not connected to the signal negative. In order to avoid hum loops, the signal negative of the whole system should be connected to the mains earth (ground) in one place. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE NAIM NAP 140




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NAIM NAP 140 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.