User manual NAIM CDP

[. . . ] OWNERS MANUAL CD Players page 1 1. 0 Equipment Installation 2 3 4 5 10 14 18 20 1. 0 Equipment installation Normally your Naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended to reduce this responsibility in any way. 21 1. 1 cables and connections 2. 0 Getting Started 2. 1 switching on and off 2. 2 running in 2. 3 mains supply 2. 4 siting the equipment 2. 5 if you have a problem 3. 0 Warnings 4. 0 Connection 4. 1 mains lead 4. 2 non-rewireable mains plugs 4. 3 fuse carrier 4. 4 plug fuses CDS Player CDX Player CD5 Player Narcom 2 Remote Control CD Player Maintenance, Specifications EC Declaration of Conformity to Appropriate Standards 1. 1 cables and connections PPlease do not modify the standard interconnect cables supplied with your Naim equipment. One end of each cable is marked with a band to establish its correct orientation. Naim loudspeaker cable is correct for your system and your dealer will make up leads to suit your equipment installation. [. . . ] Make sure it is seated properly. 8 CDS Player (from serial no. 146541) (continued) cds player operation 2 Place the disc clamp on the compact disc 3 Close the door 4 Press play 9 cdx CDX Player Operation There are four buttons situated on the right hand side of the front panel. Two of these buttons operate differently depending on whether the player is in load condition (before the play button has been pressed). The player returns automatically to load condition either at the end of the last track of a programme or when the drawer is opened and closed. previous In load condition searches the table of contents backwards, either one track at a time, or sequentially if you hold the button depressed. In play condition mutes while searching the table of contents backwards, and then plays the track chosen without further command. next The next function operates in the same way as the previous function, but moving forwards through the disc instead of backwards. stop Stops the disc rotating, returns the laser to its inner position, and resets the player to load condition. play Causes the player to enter play condition. The loaded disc will start to play, beginning with track one, unless another track has been selected. If you press play while a track is already playing, the track will be re-started. When an HDCD encoded compact disc is loaded the CDX automatically recognises it and decodes the relevant information. The display will read HDCD for a few seconds after play is pressed (from load condition). These functions are duplicated on the remote control which also provides many additional facilities. On the far right of the display are four indicators. pause When lit, the display shows that pause has been selected from the remote control. time When lit, the display shows total time (in load condition) or elapsed time of track being played (in play condition). To the left of these indicators is an alphanumeric display for track and index numbers, OR time in minutes and seconds, OR various system messages (eg: play, err etc). The full stop on the right of the window comes on when the player receives a signal from the remote control. repeat Shows, when lit, that repeat has been selected when using the remote control. program Shows, when lit, that a program has been stored. For further information please refer to page 18. 10 CDX Player previous next stop play pause time repeat program power mains input link plug fitted to preamplifier CDX output ch1 ch 2 -ve nc nc Connection to optional xps power supply (for improved performance) link plug removed NB - when using the XPS the mains lead to the CDX must be disconnected mains input cable direction marker Interconnect Cables 5 to 5 pin DIN 11 to 11 pin Burndy 11 CDX Player transit lock 1 Remove the transit screw (keep safe). Always replace this before transit or shipping. cdx player operation 1 Open the door. 12 CDX Player cdx player operation (continued) 2 Place the compact disc on the platter. Make sure it is seated properly. 3 Place the clamp on the compact disc. 4 Close the door. 5 Press play 13 cd5 CD5 Player Operation There are four buttons situated on the right hand side of the front panel. Three of these buttons operate differently depending on whether the player is in load condition (after the PLAY button has been pressed). The player returns automatically to load condition either at the end of the last track of a program or when the drawer is opened and closed. previous In load condition searches the table of contents backwards, either one track at a time, or sequentially if you hold the button depressed. In play condition mutes while searching the table of contents backwards, and then plays the track chosen without further command. next The next function operates in the same way as the previous function, but moving forwards through the disc instead of backwards. stop Stops the disc rotating, returns the laser to its inner position, and resets the player to load condition play. play Causes the player to enter play condition. The loaded disc will start to play, beginning with track one, unless another track has been selected. If you press play while a track is already playing, the track will be re-started. These functions are duplicated on the remote control which also provides many additional facilities. [. . . ] To return to the default settings, press and hold the prog key until the amplifier volume control indicator flashes. Press and hold disp key until the volume control indicator stops flashing. In cd mode the prog key enables specific CD tracks and their play order to be selected. To select a play order select a track number from the numeric keypad followed by the prog key until the desired selection is complete. [. . . ]