User manual MYRYAD MP100

[. . . ] The MP 100 should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided. CAUTION: TO PREVENT A FIRE OR SHOCK HAZARD, DO NOT PERMIT THIS PRODUCT TO BECOME WET. IF LIQUID IS ACCIDENTALLY SPILLED ON IT, IMMEDIATELY SHUT OFF ITS POWER AT THE WALL SOCKET AND UNPLUG THE AC POWER CORD. ALLOW SUFFICIENT TIME FOR COMPLETE EVAPORATION TO OCCUR BEFORE OPERATING THE PREAMPLIFIER AGAIN. [. . . ] In a normal preamp/power amp system, use the Line 1 outputs to drive the inputs of your stereo power amplifier (such as the Myryad MA 120). In a "bi-amplifier" system connect the Line 1 outputs to one stereo power amplifier (driving e. g. the treble sections of the loudspeakers) and connect the Line 2 outputs to the second stereo power amplifier (driving the bass sections of the 8 CD input Connect the audio output cables from a CD player to these sockets. (NOTE: this input is for an audio signal, not for the digital output 3 2 from your player. ) If you do not have a CD player then any other line level source may be connected to this input. operating your system standby phones tape 1 tape 2 cd video tuner aux 9 Video input Connect the audio signal output cables from a video-related source such as video cassette recorder or TV set to these sockets. Alternatively any other line level source may be connected to this input. 10 Tuner input Connect the audio output cables from a radio tuner to these sockets. If you do not have a tuner then any other line level source may be connected to this input. 11 AUX input The audio output from any line level source may be connected to this input. Alternatively a Myryad Module may be fitted internally in your MP 100 to convert this input for other applications ­ such as phono cartridge input for a record player. Your Myryad dealer can advise you on what Modules are currently available. Please follow the instructions supplied with the Module when making all connections. front panel controls 1 Standby When the preamplifier is plugged into a live wall socket and the POWER switch is turned ON, it will power up in "standby" mode and the LED (Light Emitting Diode) in the STANDBY button will glow red. In this mode the internal circuitry of the MP 100 is powered up but isolated by relays at its inputs and outputs and consumes very little power. When the STANDBY button is pressed the preamplifier circuitry will be activated and the input used last automatically selected. The LED in the STANDBY button will change to blue, the LED in the button of the selected input will light up and, after a few seconds delay, the line outputs will be connected to the preamplifier. During this delay period the LED in the volume control knob will flash to indicate that the line and headphones outputs are muted. When first switched out of STANDBY after POWER ON, the CD input will be selected by default. When the STANDBY button is pressed again the preamplifier will be returned to standby mode. The LED in the STANDBY button will glow red again and all other LEDs on the preamplifier will be extinguished. CAUTION: WHEN IN STANDBY MODE THE INTERNAL CIRCUITRY OF THE MP 100 IS STILL LIVE, SO ALL SAFETY PRECAUTIONS MUST BE FOLLOWED. therefore not be obscured when the preamplifier is to be operated using the remote control handset. Where possible it is best to arrange that the IR window is in "line-of-sight" of the remote handset. the rear panel. This is a "toggle" function switch: you press it once to engage and press again to disengage. The blue LED in the centre of the TAPE 1 button illuminates to indicate that TAPE 1 is engaged. Pressing the TAPE 1 button has no effect on the other input select buttons. The signal source selected by the other input select buttons will be fed to the TAPE 1 REC output sockets, irrespective of whether the TAPE 1 button is engaged or not. [. . . ] The line outputs are also muted when the MUTE button on the R/C handset is pressed. It is recommended that the preamplifier be switched into mute before changing input or output interconnects. Physical Specification Dimensions (width x height x depth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436 x 95 x 303mm Weight Net: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. 3kg Power Requirements Voltage (set by internal wiring) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120/230V Stock No: OST0011740 Revision A remote control handset operation The nine keys at the top of the handset operate the MP 100. The first six keys (CD, TUNER, AUX. , TV, TAPE 1 and TAPE 2) function in exactly the same way as their counterparts on the front panel, allowing any input source to be selected for listening or recording. Pressing one of the VOLUME 5 or 6 keys will cause the motorised volume control in the preamplifier to rotate clockwise or anticlockwise respectively. [. . . ]