User manual MPMAN PDV 2000

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) when the power-supply or plug is damaged; b) if liquid has been spilled or if objects have fallen into the product; c) if the product has been exposed to rain or water; d) if the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation; e) if the product has been dropped or damaged in any way; f) when the product exhibits a distinct change in performance--this indicates a need for service. Replacement Parts: When replacement parts are required, be sure that your service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to ensure that the product is in proper operating condition. Wall or Ceiling Mounting: The product should be mounted to a wall or ceiling only as recommended by the manufacturer. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 15 Outputting AV signal from the main unit to the monitor by the DC car cord . Disc Requirements This DVD player supports playback of the following discs. This unit can play back CD-R and CD-RW discs that contain JPEG picture files. Discs not listed above are not supported by this unit (eg, PC CD-ROM, CD-Extra, CD-G, CD-I, etc. To remove a DVD/CD from its storage case, press down on the center retention mechanism of the case and lift the disc out. To reduce the risk of scratches, always put discs back in their case after use. Cleaning a Disc Use a dry, soft cloth to wipe off any fingerprints and dusts from the playing surface of the disc. Wipe in a straight line radially from the center to the outside edge of the disc. Small dust particles and light stains will not affect playback quality. Never use chemicals such as record sprays, anti-static sprays, benzene, or thinners to clean a disc. Point the remote at the remote sensor of the photo frame at a distance of no more than 15 feet and at an angle no greater than 60 degrees. Remove the batteries if the remote control will not be in use for an extended period of time. Power, Audio and Video Output Connections Before connecting the power source, ensure that all the connections are properly done. Connecting to a wall outlet Outputting audio and video signal from the main unit to the monitor by the DC car cord. AC/DC adaptor for main unit: This AC/DC adaptor should be used with 100-240V~50/60Hz 0. [. . . ] After 30 minutes, plug in and power on the player -- the restore function should reset the player. Ensure that the AC adaptor cord is securely connected to the player and the proper wall outlet. This is to certify that the portable DVD palyer is conformity with council directive 2004 / 108 / EC(EMC Directive) Applicable standards EN55013:2001+A1+A2 EN61000-3-2:2006 EN61000-3-2:2008 EN55020:2007 For more information please visit our website www. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. [. . . ]