User manual MPMAN ICR 110

[. . . ] Near sources of strong magnetism, such as television, speakers or magnets. Where there is a lot of movement or vibration, such as on a car dashboard or an unstable shelf. For safety Do not attempt to disassemble this unit. make sure that pins or other foreign objects to not get inside the Unit. Take care not to drop the unit or subject it to strong shocks. Note no listening with the earphones listen at moderate volumes to avoid hearing damage. [. . . ] Do not try to recharge batteries not intended to be recharged;they can overheat and rupture. (Follow battery manufacturer's directions. ) Press and hold the MODE/PAUSE button 1 for two seconds; "SET" will appear and When the desired recording quality appears, press the MODE/PAUSE button twice to confirm and return to the Time mode or it will change to the Time mode if no button is pressed in 30 seconds. Long Play:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3369 min . the recording quality will blink press the REV 2 or FWD 3 button to select the desired recording quality. 4 6 OPERATION SETTING THE TIME AND DATE When the batteries are inserted, 0 hour and 0 min and Jan01 will appear in the display. Set the time and date as follows: 1 2 OPERATION(CONTINUED) SELECTING A FILE FOLDER This unit has four memory storage areas(file folders)to choose from, labelled A, B, C and D. You can store 99 messages in each individual file folder, for four file folder you can totally save 396pcs of messages. 1 NOTE: Each time you record a message, The unit will assign a number, counting up 1 from the last message number, which will be shown on the display. 2 REV FWD E R A S E / R E P E AT REC/ STOP P L AY / S T O P 1 2 REV FWD E R A S E /R E P E AT RE C/ STOP P L AY /S T O P 3 1 Press the REC/STOP 1 or PLAY/STOP 2 button to enter the standby mode. Press the FILE/TIME button 3 to select the desired file folder (A, B, C, D). The number at the top right of the display indicates the total messages recorded. The number at the bottom of the display will indicate the total time recorded for the selected message. While the date/time appears in the display, press the FILE/TIME button 1 to shift between 12 or 24 time display. Press and hold the Mode/Pause button 2 for two seconds, then release, 'SET' will appear in the display. Press the Mode/Pause button 2 once again to enter the Date /Time set mode. Press the PLAY/STOP button 1 to confirm and the year will blink. Set the year using the REV 2 and FWD 3 buttons, then press the PLAY/STOP button 1 again to confirm. If the unit is full, FULL will appear in the display. Delete messages in this case. 3 RECORDING 1 SENSITIVITY 2 HOLD SWITCH 2 REV FW D E R A S E / R E P E AT R EC / S TO P P L AY / S T O P 3 1 Set the Month using the REV 2 and FWD 3 buttons, then press the PLAY/STOP button 1 again to confirm. Repeat this step to set the Day, Hour and Minute. Slide the MIC SENS switch to the LOW position if recording sounds that are close. Select the HIGH position if recording sounds that are further away. Slide the HOLD switch to the LOCK position to disable the buttons; HOLD will appear in the display. Slide the HOLD switch to the OFF Position to enable the buttons again. 5 7 OPERATION(CONTINUED) NORMAL RECORDING This unit is capable of recording only when sound is heard. For normal recording, follow steps below. OPERATION(CONTINUED) TO PLAY BACK MESSAGES 1 2 1 2 Turn the unit on and select a File Folder by pressing the FILE/TIME button(see page7). Turn the unit on, and select the desired sound quality as described on page 6. Select a File Folder by pressing the FILE/TIME button (see page7). Select the desired message number by pressing the REV 1 or FWD 2 button; the message number and the message length will appear in the display. 3 3 4 While in the standby mode, press the PLAY/STOP button 1 ; the unit will play the currently selected message, then stop. During playback, the play indicator and the elapsed time of the message will appear in the display. You can check the message recording time and date by pressing the REC/STOP button 2 . While in the standby mode, press the REC/STOP button and the REC indicator will light and the elapsed time will appear. Speak into the built-in microphone or insert a microphone into the MIC jack and speak to it with a normal tone of voice. [. . . ] TO PAUSE A MESSAGE Press the REC/STOP button and the REC indicator will light and the elapsed time will appear. Speak into the built-in microphone or insert a micro-phone into the MIC jack and when the unit picks up sound, it will record. When not recording , the REC indicator will blink and PAUSE will blink in the display until sound is detected. . To pause, press the MODE/PAUSE . The built-in audio level automatically sets the recording level. [. . . ]