User manual MPMAN FRA 200

[. . . ] Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. A Consumer Guide to Product Safety IMPORTANT SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK). WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle is intented to alert the user to the presence of uninsulated `dangerous voltage` within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. 1. ) 2. ) 3. ) 4. ) 5. ) 6. ) 7. ) 8. ) 9. ) 10. ) 11. ) 12. ) The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The symbols above are located at the bottom of the cabinet. [. . . ] When moving the set, be sure to first disconnect the power cord and remove cords connected to other equipment. 3 13 Clock Adjust Button Sleep Button Time Set Up Button Time Set Down Button Alarm 1 Button Alarm 2 Button Tuning Control 14 Radio Band Button Volume Control 15 16 4 LED Display Setting Clock Time 1. When you first plug the unit into the AC outlet, the unit will be in standby mode. Press & hold the C-ADJ Button more than 2 seconds, the `HOUR` LED indicator will flash and then press the Time Set `Up` or Time Set `Down` button for hour adjustment. Then, the `MINUTE` LED indicator will flash and then press the Time Set `Up` or Time Set `Down` button for minute adjustment. Then, the `WEEK DAY` LED indicator `d1` will flash then press the Time Set `Up` or Time Set `Down` button for week day adjustment. (`d1` means Monday and `d7` means Sunday) 5. Press the C-ADJ Button to confirm the Weekday set. Time/Radio Frequency Indicator FM Dot Indicator Standby Indicator PM Indicator MW Band Indicator FM Band Indicator Listening to Radio HOUR Indicator MINUTE Indicator Tuner Information This system features a normal MW/FM analog tuning system. It does not automatically lock in on the exact frequency of a station. However instead of a dial scale and a moving dial pointer we have included a digital frequency display to help you tune more accurately. Do not be concerned If you cannot easily tune the display to the exact frequency of your favourite stations, especially on the MW band. Slowly rotate the TUNING control until the display approaches the frequency of the desired station and stop when get the strongest, noise free reception-even if the display is not indicating the exact frequency of desired station. Battery Backup Installation Memory Backup To insert 1. 5V x 2, R03S/ AAA or equivalent batteries in the battery compartment at the bottom of the unit. Note: You should replace the battery every six months, or after any extended power outage that could drain the battery power. Radio Operation Press the POWER / ALARM RESET button on the unit to switch the unit ON. After 10 seconds, the display will go back to Real Time Clock. 6 5 Listening to Radio ANTENNA FM For FM reception there is a built-in FM antenna wire at the rear of the unit. To improve MW reception, you may have to move or slightly rotate the main unit until you obtain in best reception. Operating the Alarms ALARM setting 1. Press & hold the ALARM 1 button more than 2 seconds, the `HOUR`& `ALARM 1` LED indicators will flash and then press the Time Set `UP` or Time Set `DOWN` Button for hour adjustment. [. . . ] If weekend sleep function is on, alarm will not function on SAT and SUNDAY even though the alarm timer is enabled and the time is matched. Display Mode setting Press the DISPLAY button changing the display as shown below. In the Standby mode : `ALARM 1` display >> `ALARM 2` display >> Clock display. In the Radio mode : Radio frequency >> `ALARM 1` display >> `ALARM 2` display >> remain time of SLEEP Timer >> Clock display. 9 As the colours of the wires in the mains lead of this apparatus may not correspond with the coloure d markings identifying the terminals in your plug, proceed as followings:The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. [. . . ]