User manual MOTO GUZZI QUOTA 1100 ES

[. . . ] The illustrations and description in this booklet are indicative only and the manufacturer reserves itself the right to introduce any modification it may deem necessary for better performance or for constructive or commercial reasons without prior notice. Dear rider First of all we wish to thank you for choosing this motorcycle of our production. By following the instructions outlined in this manual you will ensure your bike a long and troublefree life. Before riding, please read thoroughly this manual in order to know your motorcycle's features and how to operate it safely. [. . . ] If no suitable lubricant is available, we recommend the light greasing of the rubber and metal parts with brake fluid. Before the end of dipstick «B» comes into contact with the brake pump master cylinder; otherwise alter the length of dipstick «B» by tightening or untightening it, after having loosened off lock nut «C». To alter the height of pedal «A» loosen off lock nut «D» and adjust screw «E», at the same time altering the length of dipstick «B» until the desired play has been achieved. 17) The motorcycle is equipped with single shock absorbers with separate adjustment of the springs pre-loading and the action of the dampers in extension. To adjust the pre-loading of the spring, remove the saddle using the correct wrench, loosen off ringnut «A» and adjust ringnut «B»; tightening up increases the spring pre-loading. : To avoid damaging the thread between the damper body and the ring nut «B», lubricated the thread with «SVITOL», with oil or with grease. To ensure safe riding, the steering should be adjusted to allow free movement of the handlebars without any play. Loosen the steering head fixing bolt «A»; undo the steering head nut «B»; turn the adjuster nut «C» to take up any play. When play has been adjusted tighten the nut «B» and the steering head fixing bolt «A». It is recommended to perform the operation described above at our dealer locations. ITEMS Engine oil Oil filter cartridge Wire gauze oil filter Air filter Fuel filter Spark plugs Rocker clearance Carburetion Nuts and bolts Fuel tank, cocks filters and pipes Gear box oil Rear drive box oil Wheel and steering bearings Fork legs oil Starter motor and generator Brake systems fluid Brake pads Occasionally, lubricate joints and cables; every 500 km (300 miles) check the engine oil level. In any case, replace the motor oil, the oil filter and the brake fluid, oil at least once a year. Preparations for washing Before washing the vehicle, the following parts should be covered with a waterproof material: the rear part of the silencers, the clutch and brake levers and pedals, the throttle twist-grip, the left-hand light switch, the ignition key switch, the shaft with driving couplings. Washing Avoid spraying water too much pressure on the instruments and the front and rear hubs. - To clean the painted parts of the engine unit (engine, gearbox, transmission box, etc. ) the following products may be used: diesel oil, petrol or water-based neutral detergents for car cleaning. These products should be washed off immediately with water; do not use water at high temperatures or pressures. If the vehicle is to remain idle for a considerable period of time (e. For the winter period) it should be stored in the following way: clean the vehicle thoroughly; empty the fuel tank and feeding system. If left for a long time, the fuel will evaporate leaving incrustation and residue; remove the spark plugs and put a few drops of SAE 30 oil into che cylinder. Turn the crankshaft for a few revolutions and then replace the spark plugs; reduce the tyre pressures by 20%; position the vehicle so that its wheels are not touching the ground; smear a layer of oil on unpainted parts to prevent rust; remove the battery and store in a dry place away from the direct sunlight and where there is not danger of frost; check the battery charge once a month; cover the vehicle but in such a way that the air can circulate. The windscreen can be cleaned using most of the soaps, cleaners, waxes and polishes commercially available for glass and plastic. [. . . ] 28) The filter is provided with a filtering element made of paper, with 1200 cm2 surface, and 10 µm; filtering power: it is necessary due to the high sensibility of injectors to foreign elements. The filter is assembled under the saddle between the pump and the pressure adjuster and on the external cover there is an arrow showing the direction of the fuel. 29) Check the air filter every 5000 km and clean by blowing with compressed air; change every 10. This filter is mounted in a special case above the motor group, the saddle and fuel tank must be removed in order to have access to it. [. . . ]