User manual METABO PKF 255 V8
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual METABO PKF 255 V8. We hope that this METABO PKF 255 V8 user guide will be useful to you.
Manual abstract: user guide METABO PKF 255 V8
Detailed instructions for use are in the User's Guide.
[. . . ] D G F
Betriebsanleitung Formatkreissäge Operating Instruction Panel sizing saw Instructions d'utilisation Scie circulaire de format
PKF 255 V8
15
45
30
0
15
30
45
D G F
Deutschland
Die beiliegende Garantiekarte senden Sie bitte an uns zurück. Ein Anspruch auf Garantieleistungen besteht nur gegen Vorlage des Kaufbelegs. Die Adresse Ihrer nächstgelegenen Werksvertretung finden Sie auf der hinteren Umschlagseite. Please see back cover for manufacturer representative´s address nearest you. [. . . ] Otherwise there is no sufficient distance between the saw blade and the hand. Slide hold-down plate from the rear into the groove of the travelling sizing table and tighten. Unlock travelling sizing table travel lock and pull travelling sizing table towards you. Place workpiece on travelling sizing table and push it against the hold-down plate. Push travelling sizing table forward to cut workpiece in a single pass. Switch machine off if no further cutting is to be done immediately afterwards. · Check that all safety devices are operational again after each service. · Replace defective parts, especially of safety devices, only with genuine replacement parts. Parts not tested and approved by the equipment maker can cause unforeseen damage. · Repair and maintenance work other than described in this section shall only be carried out by qualified specialists.
PKF 255 V8
2. 11
Main saw blade change
A Danger!injury by the saw blade's teeth. The cover is hooked into the bottom of the chip case and can not fall down.
A Danger!for removing Do not use
resin residue) that could corrode the light metal components of the saw; the stability of the saw would be adversely affected. The saw spindle's driving pin must fit into one of the saw blade's two pin holes.
A Danger!suitable saw blades (see , , Technical Use only
specifications") when using unsuitable or damaged blades parts could be explosivelike hurled from it by the centrifugal force. Do not use: - saw blades made of high speed steel (HSS); - saw blades with visible damage; - cut-off wheel blades.
5. To block the saw blade insert lock bar into hole in the saw table and turn saw blade by hand until lock bar engages in saw spindle hole.
- Do not use loose-fitting reducing rings; the saw blade could work loose. - Saw blades have to be mounted in such way that they do not wobble or run out of balance, and can not work loose during operation. The saw spindle's driving pin must fit into the pin hole of the outer blade collar. Screw arbor nut, with the low side facing the blade, onto the saw spindle (L. H. - After tightening the arbor nut do not forget to remove the saw spindle lock bar!Slide chip case cover back into the closed position and tighten screws. - Do not
2. 12
PKF 255 V8
Main saw blade adjustment
The saw blade must run exactly parallel with the saw table's edge. [. . . ] out any fault service or mainBefore carrying
tenance work always: - Switch machine OFF. Check that all safety devices are operational again after each fault service. by - a dull saw blade - too high a feed rate - sawdust build-up in housing. Eliminate cause for overheating, wait for a few minutes, then start saw again.
Visual check if distance saw blade riving knife is 3. . . 8 mm. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE METABO PKF 255 V8
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual METABO PKF 255 V8 will begin.