User manual MEMOREX MC2850-02OM

[. . . ] Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. Only qualified service personnel should attempt to service this device due to possible eye injury. CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE PROCEDURE HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. SURGE PROTECTORS: It is recommended to use a surge protector for AC connection. [. . . ] NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. OUTDOOR ANTENNA GROUNDING If an outside antenna is connected to the product, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electric Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge product, size of grounding conductors, location of antenna discharge product, connection to grounding electrodes and requirements for grounding electrodes. c. 23. f. 24. 3 EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE Dear Customer: Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion--and, most importantly, without affecting your sensitive hearing. Over time your hearing "comfort level" adapts to higher volumes of sound. So what sounds "normal" can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts. To establish a safe level: · Start your volume control at a low setting. · Slowly increase the sound until you can hear it comfortably and clearly, and without distortion. 10 seconds on the display. 10 TO REPEATEDLY PLAY BACK ONE TRACK 1 OPERATION (CONTINUED) 2 2 3 1 1 2 With a CD inserted, press the POWER button 1 to turn the unit on. Repeatedly press the FUNCTION button 2 to select CD; "CD" will appear in the display; the total number of tracks will appear in the display. Press the Play/Pause (®p) button 1 to start playback; "PLAY" will appear in the display. Press the SKIP/SEARCH l 2 or m 3 button to select a track to repeat. 3 1 2 TO REPEATEDLY PLAY BACK ALL TRACKS 1 2 1 Press the REPEAT button 1 once; "REPEAT" will appear in the display and the unit will play the same track over and over until the STOP (s) button 2 is pressed. Follow steps 1 and 2 above, but do not select a specific track. Press the REPEAT button 1 twice; "REPEAT ALL" will appear in the display and the unit will play all the tracks on the CD over and over until the STOP (s) button 2 is pressed. TO CANCEL REPEAT MODE, press the REPEAT button twice. TO CANCEL REPEAT ALL MODE, press the REPEAT button once. 11 TO PROGRAM THE MEMORY (UP TO 32 TRACKS) 1 OPERATION (CONTINUED) 1 2 3 2 2 1 With a CD inserted, press the POWER button 1 to turn the unit on. Repeatedly press the FUNCTION button 2 to select CD; "CD" will appear in the display; the total number of tracks will appear in the display. 3 Press the PLAY/PAUSE (®p) button to begin playback. The unit will play all the tracks in the order you programmed them; both "PROG" and "PLAY" will appear in the display. Press the PROGRAM button 1 once; "PROG" will blink and "1" (program number) will appear in the display. Select the first track to be played back using the SKIP/SEARCH l 2 or m 3 button ("PROG" will not blink while the track is being selected), then press the PROGRAM button 1 again. Repeat this step to program additional tracks, up to 32 tracks. 4 1 2 When the disc is through playing, it will stop. Press the POWER button 2 to turn the unit off. NOTES: · To skip forward or backward through the programs, press the Skip/Search l or m button. · Programming is the ability to preselect the order in which a series of tracks will be played. [. . . ] If you select a starting track higher than the track numbers on the CD, the unit will start playback on the first track and play up to 60 minutes. · TO SHUT OFF THE ALARM, see TO SHUT THE ALARM OFF section on the next page. · While the alarm is sounding, if the other alarm reaches the alarm time, the first alarm will stop sounding and the second alarm will start sounding. · Make sure you have disconnected the headphones from the Headphones jack (rear of the unit) and disconnected the audio cable from the AUX IN jack (rear of the unit); otherwise, there will be no sound when the actual time matches the preset alarm time. 18 TO SHUT THE ALARM OFF 1 OPERATION (CONTINUED) To shut the alarm off, press the POWER button 1 and the alarm time will be reset for the next day. [. . . ]