User manual MEMOREX MC2850-01OM

[. . . ] Avoid direct exposure to beam. FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. Only qualified service personnel should attempt to service this device due to possible eye injury. [. . . ] SAFETY CHECK Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. WALL OR CEILING MOUNTING The product should be mounted to a wall or ceiling only as recommended by the manufacturer. DAMAGE REQUIRING SERVICE Unplug the product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power-supply cord or plug is damaged. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. When the product exhibits a distinct change in performance - this indicates a need for service. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. NONUSE PERIODS The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. 11. 19. 20. 21. 12. a. 22. 15. 23. 16. 17. 24. 18. 3 Dear Customer: Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. If the device is not to be used for a long period of time, remove the battery to prevent damage or injury from possible battery leakage. Do not try to recharge a battery not intended to be recharged; it can overheat and rupture. NOTES: · If a disc is inserted incorrectly, dirty, damaged or not present at all, the display will show, "no". 8 OPERATION (CONTINUED) TO REPEATEDLY PLAY BACK ONE TRACK 1 1 2 2 1 4 3 3 2 Press the POWER/ALARM RESET button 1 to turn the unit on; the POWER indicator will light. Press the P-MODE button 3 once; the REPEAT indicator will blink. Press the SKIP n 1 or o 2 button to select a desired track and within 2 second, press the PLAY/PAUSE (®p) button 3 to start playback and the unit will play the same track over and over until the STOP (I) button 4 is pressed. TO REPEATEDLY PLAY BACK ALL TRACKS 1 1 2 2 2 1 3 Press the POWER button 1 to turn the unit on; the POWER indicator will light. Press the P-MODE button 3 twice; the REPEAT indicator will light solid. Press the PLAY/PAUSE (®p) button 1 to start playback and the unit will then play all the tracks on the CD over and over until the STOP (I) button 2 is pressed. NOTE: To stop and cancel repeat playback, press the STOP (I) button once. 9 OPERATION (CONTINUED) TO RANDOMLY PLAY BACK A CD 1 1 2 2 2 3 1 Press the POWER/ALARM RESET button 1 to turn the unit on; the POWER indicator will light. Press the P-MODE button 3 3 times; the RANDOM indicator will light. Press the PLAY/PAUSE (®p) button 1 to begin playback, the unit will play all the tracks on the CD randomly. Press the STOP (I) button 2 to stop the disc before it is finished. NOTE: To stop and cancel random playback, press the STOP (I) button once. 10 OPERATION (CONTINUED) TO PROGRAM THE MEMORY (UP TO 20 TRACKS) 1 1 2 2 1 2 3 Select the first track to be played back using the SKIP n 1 or o 2 button, then press the PROG. Repeat this step to program additional tracks up to a maximum of 20 tracks. 3 Press the POWER/ALARM RESET button 1 to turn the unit on; the POWER indicator will light. button 3 once; "P 01" will briefly appear in the display and the PROGRAM indicator will blink. 3 4 2 1 Press the PLAY/PAUSE (®p) button to begin playback. [. . . ] Press the ALARM button (ALARM 1 or ALARM 2) 2 twice to turn off the alarm. The ALARM 1 or ALARM 2 indicator will disappear in the display and the alarm will not be set for the next day. SNOOZE 1 The alarm can be temporarily turned off manually by pressing the SNOOZE button; the alarm will turn back on automatically 6 minutes later. It can be repeated endlessly. NOTE: If both ALARM 1 and ALARM 2 are set, the Snooze feature will only operate up to the next alarm. If the next alarm time is reached, the unit automatically turns on for 59 minutes and then shuts off. [. . . ]